Nissan Titan A60. Manual — part 728
MWI-26
< SYSTEM DESCRIPTION >
COMPASS
1. Determine your location on the zone map.
2. Turn the ignition switch to the ON position.
3. Press and hold the (N) switch (with HomeLink universal transceiver) or the mode switch (without
HomeLink universal transceiver) until the current zone number appears in the display.
4. Press the mode or (N) switch repeatedly until the desired zone number appears in the display.
Once the desired zone number is displayed, stop pressing the mode or (N) switch and the display will show a
compass direction after a few seconds.
NOTE:
Use zone number 5 for Hawaii.
CALIBRATION PROCEDURE
The compass display is equipped with an automatic correction function. If the compass display reads “CAL” or
the direction is not shown correctly, perform the correction procedure below.
1. Press and hold the (N) switch (with HomeLink universal trans-
ceiver) or the mode switch (without HomeLink universal trans-
ceiver) until the display reads “CAL”.
2. Drive the vehicle slowly in a circle, in an open, safe place. The
initial calibration is completed in about 3 turns.
NOTE:
In places where the terrestrial magnetism is extremely disturbed, the
initial correction may start automatically.
WKIA4889E
MWI
DIAGNOSIS SYSTEM (METER)
MWI-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (METER)
Diagnosis Description
INFOID:0000000006164908
SELF-DIAGNOSIS MODE
The following items can be checked during Combination Meter Self-Diagnosis Mode.
• Gauge sweep and present gauge values.
• Illuminates all odometer/trip meters and A/T indicator segments.
• Illuminates all micro controlled lamps/LEDs regardless of switch position.
• Displays estimated present battery voltage.
• Displays seat belt buckle switch LH status.
OPERATION PROCEDURE
NOTE:
• Once entered, combination meter self-diagnosis mode will function with the ignition switch in ON or START.
Combination meter self-diagnosis mode will exit upon turning the ignition switch to OFF or ACC.
• If the diagnosis function is activated with trip A displayed, the mileage on trip A is reset to 0000.0. (Trip B
operates the same way.)
To initiate combination meter self-diagnosis mode, refer to the following procedure.
1. Turn the ignition switch ON, while pressing the odometer/trip meter switch for 5 - 8 seconds. When the
diagnosis function is activated, the odometer/trip meter will display tESt.
NOTE:
Check combination meter power supply and ground circuit when self-diagnosis mode of combination meter
does not start. Refer to
MWI-33, "COMBINATION METER : Diagnosis Procedure"
. Replace combination
meter if normal. Refer to
MWI-93, "Removal and Installation"
.
COMBINATION METER SELF-DIAGNOSIS MODE FUNCTIONS
To interpret combination meter self-diagnosis mode functions, refer to the following table.
Event
Odometer Display
Description of Test/Data
Notes:
Odometer/trip meter A/B
switch held from 5 to 8
seconds (or until re-
leased)
tESt
Initiating self-diagnosis mode
Switch released
GAGE
Performs sweep of all
gauges, then displays
present gauge values.
Gauges sweep within 10 seconds
Switch pressed
(All segments illuminated)
Lights all LCD segments.
Compare with picture.
Switch pressed
bulb
Illuminates all micro-con-
trolled lamps/LEDs.
Part may not be configured for all
lamps (functions) that turn on dur-
ing test. This is normal.
Switch pressed
r XXXX, FAIL
Return to normal opera-
tion of all lamps/LEDs and
displays “r XXXX”.
If a malfunction exists, “FAIL” will
flash.
Switch pressed
nrXXXX
Displays Hex ROM rev as
stored in NVM.
Switch pressed
EE XX, FAIL
Displays “EE XX”.
If a malfunction exists, “FAIL” will
flash.
Switch pressed
dtXXXX
Hex coding of final manu-
facturing test date.
ALNIA0280ZZ
MWI-28
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (METER)
CONSULT-III Function (METER/M&A)
INFOID:0000000006164909
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF-DIAG RESULTS
Display Item List
Switch pressed
(3 times)
Sc1 XX through Epr XX
Displays 8 bit software
configuration value in Hex
format
Switch pressed
1nF XX
Displays 8-bit market info
value in Hex format.
$31 = USA
$2A = Canada
Switch pressed
(3 times)
cYL XX through tF
N/A
Switch pressed
ot1 XX
Displays oil pressure tell-
tale “” in Hex format.
Switch pressed
ot0 XX
Displays oil pressure tell-
tale “” in Hex format.
Switch pressed
XXXXX
“Corrected” speed value
in hundredths of MPH.
Gauge indication may be
slightly higher. This is nor-
mal.
Will display “-----” if message is not
received. Will display “99999” if
data received is invalid.
Switch pressed
XXXXX
“Corrected” speed value
in hundredths of KPH.
Gauge indication may be
slightly different. This is
normal.
Will display “-----” if message is not
received. Will display “99999” if
data received is invalid.
Switch pressed
t XXXX
Tachometer value in
RPM. Gauge indication
may be higher at higher
RPM. This is normal.
Will display “-----” if message is not
received.
Switch pressed
F1XXXX
Present fuel level A/D in-
put. This input represents
fuel sender input.
000-009 = Short circuit
010-254 = Normal range
255 = Open circuit
Switch pressed
F2XXX
Present FLPS.
010-254 = Normal range
Switch pressed
XXXC
Last temperature gauge
input value in degrees C.
Temperature gauge indi-
cates present tempera-
ture per indication
standard.
Will display “---”C if message is not
received.
Will display “999” if data received
is invalid.
High = 130 deg C
Normal = 70 - 105 deg C
Low = less than 50 deg C
Switch pressed
BAtXX.X
Estimated present battery
voltage.
Switch pressed
rES -X
Seat belt buckle switch LH
status.
1= Buckled
0 = Unbuckled
Switch pressed
(33 times)
PA -XX through PA1-XX
N/A
Switch pressed
GAGE
Return to beginning of self-diagno-
sis cycle.
Event
Odometer Display
Description of Test/Data
Notes:
METER/M&A diagnosis mode
Description
SELF DIAGNOSTIC RESULT
Displays combination meter self-diagnosis results.
DATA MONITOR
Displays combination meter input/output data in real time.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
MWI
DIAGNOSIS SYSTEM (METER)
MWI-29
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
.
DATA MONITOR
Display Item List
X: Applicable
Display item [Unit]
MAIN
SIGNALS
SELECTION
FROM MENU
Description
SPEED METER [km/h] or [mph]
X
X
Displays the value of vehicle speed signal.
SPEED OUTPUT [km/h] or [mph]
X
X
Displays the value of vehicle speed signal, which is transmitted to
each unit with CAN communication.
TACHO METER [rpm]
X
X
Displays the value of engine speed signal, which is input from ECM.
W TEMP METER [
°C] or [°F]
X
X
Displays the value of engine coolant temperature signal, which is in-
put from ECM.
FUEL METER [lit.]
X
X
Displays the value, which processes a resistance signal from fuel
gauge.
DISTANCE [km] or [mile]
X
X
Displays the value, which is calculated by vehicle speed signal, fuel
gauge and fuel consumption from ECM.
FUEL W/L [ON/OFF]
X
X
Displays [ON/OFF] condition of fuel warning lamp.
C-ENG W/L [ON/OFF]
X
Displays [ON/OFF] condition of malfunction indicator lamp.
AIR PRES W/L [ON/OFF]
X
Displays [ON/OFF] condition of tire pressure warning lamp.
SEAT BELT W/L [ON/OFF]
X
Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF]
X
X
Displays [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF]
X
Displays [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF]
X
Displays [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF]
X
Displays [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF]
X
Displays [ON/OFF] condition of oil pressure warning lamp.
VDC/TCS IND [ON/OFF]
X
Displays [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF]
X
Displays [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF]
X
Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF]
X
Displays [ON/OFF] condition of brake warning lamp.*
M RANGE SW [ON/OFF]
X
X
Displays [ON/OFF] condition of manual mode range switch.
NM RANGE SW [ON/OFF]
X
X
Displays [ON/OFF] condition of except for manual mode range
switch.
AT SFT UP SW [ON/OFF]
X
X
Displays [ON/OFF] condition of A/T shift-up switch.
AT SFT DWN SW [ON/OFF]
X
X
Displays [ON/OFF] condition of A/T shift-down switch.
BRAKE SW [ON/OFF]
X
Indicates [ON/OFF] condition of parking brake switch.
AT-M GEAR [1, 2, 3, 4, 5]
X
X
Indicates [1, 2, 3, 4, 5] condition of A/T manual mode gear position.
P RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift P range indicator.
R RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift R range indicator.
N RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift N range indicator.
D RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift D range indicator.
4 RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift 4 range indicator.
3 RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift 3 range indicator.
2 RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift 2 range indicator.
1 RANGE IND [ON/OFF]
X
X
Indicates [ON/OFF] condition of A/T shift 1range indicator.
AT CHECK W/L [ON/OFF]
X
Displays [ON/OFF] condition of AT CHECK warning lamp.
CRUISE IND [ON/OFF]
X
Displays [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF]
X
Displays [ON/OFF] condition of SET indicator.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст