Nissan Titan A60. Manual — part 327
DIFF LOCK INDICATOR LAMP FLASHES WHILE DRIVING
DLN-247
< SYMPTOM DIAGNOSIS >
[REAR FINAL DRIVE: M226 (ELD) ]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DIFF LOCK INDICATOR LAMP FLASHES WHILE DRIVING
Description
INFOID:0000000006179617
The DIFF LOCK indicator lamp will flash once every 2 seconds when the differential lock system is in standby
condition. Standby condition is the time between when the differential lock mode switch is turned ON and
when the differential lock control unit see’s all conditions are met to engage the differential lock. The DIFF
LOCK indicator lamp should be OFF if there has been a fault detected. For more information regarding the dif-
ferential lock system operation, refer to the Owner’s Manual.
Inspection Procedure
INFOID:0000000006179618
SYMPTOM:
DIFF LOCK indicator lamp sometimes flashes while driving.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
DLN-216, "CONSULT-III Function (DIFF LOCK)"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
.
NO
>> GO TO 2.
2.
CHECK DIFFERENTIAL LOCK MODE SWITCH
Perform trouble diagnosis for differential lock mode switch. Refer to
DLN-224, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Condition is intermittent. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning component.
DLN-248
< PRECAUTION >
[REAR FINAL DRIVE: M226 (ELD) ]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006179619
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution
INFOID:0000000006179620
• Before connecting or disconnecting differential lock control
unit harness connector, turn ignition switch “OFF” and dis-
connect the battery cable from the negative terminal. Because
battery voltage is applied to differential lock control unit even
if ignition switch is turned “OFF”.
• When connecting or disconnecting pin connectors into or
from differential lock control unit, take care not to damage pin
terminals (bend or break).
When connecting pin connectors make sure that there are not
any bends or breaks on differential lock control unit pin termi-
nal.
SEF289H
SEF291H
PRECAUTIONS
DLN-249
< PRECAUTION >
[REAR FINAL DRIVE: M226 (ELD) ]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Before replacing differential lock control unit, perform differ-
ential lock control unit input/output signal inspection and
make sure whether differential lock control unit functions
properly or not. Refer to
Precaution for Servicing Rear Final Drive
INFOID:0000000006179621
• Before starting diagnosis of the vehicle, understand the symptoms well. Perform correct and systematic
operations.
• Check for the correct installation status prior to removal or disassembly. When matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.
• Overhaul should be done in a clean work area, a dust proof area is recommended.
• Before disassembly, completely remove sand and mud from the exterior of the unit, preventing them from
entering into the unit during disassembly or assembly.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or a shop cloth to prevent the entering of lint.
• Check appearance of the disassembled parts for damage, deformation, and abnormal wear. Replace them
with new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time the unit is disassembled.
• Clean and flush the parts sufficiently and blow them dry.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mating surface; then remove any moisture, oil, and
foreign materials from the application and mating surfaces.
• In principle, tighten nuts or bolts gradually in several steps working diagonally from inside to outside. If a
tightening sequence is specified, observe it.
• During assembly, observe the specified tightening torque.
• Add new differential gear oil, petroleum jelly, or multi-purpose grease, as specified.
SDIA1848E
DLN-250
< PREPARATION >
[REAR FINAL DRIVE: M226 (ELD) ]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006179622
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST33290001
(J-34286)
Puller
Removing front oil seal
ST15310000
(
—
)
Drift
Installing front oil seal
a: 96mm (3.77 in) dia.
b: 84 mm (3.30 in) dia.
ST3127S000
(J-25765-A)
Preload gauge set
1.
GG91030000
(J-25765)
Torque wrench
2.
HT62940000 (1/2
″)
(
—
)
Socket adapter
3.
HT62900000 (3/8
″)
(
—
)
Socket adapter
Inspecting drive pinion bearing preload
torque and total preload torque
—
(C-4164)
Adjuster tool
Removing and installing side bearing ad-
juster
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ZZA0601D
NT115
NT124
WDIA0192E
S-NT046
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст