Nissan Titan A60. Manual — part 154
FRONT DISC BRAKE
BR-43
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
3. Apply clean brake fluid to pistons (1), then install pistons into cyl-
inder body and insert piston boot (2) side lip into groove of pis-
tons as shown.
CAUTION:
Press pistons evenly and vary the pressing point to prevent
cylinder inner wall from being rubbed.
4. Install new sliding pins and sliding pin boots to torque member.
5. Install cylinder body. Tighten sliding pin bolts to the specified torque.
JPFIA0041ZZ
BR-44
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DISC BRAKE
REAR DISC BRAKE
Disassembly and Assembly
INFOID:0000000006163305
DISASSEMBLY
1. Remove pads from cylinder body.
2. Remove sliding sleeve and boot from cylinder body.
3. Place a wooden block as shown, and blow air into union bolt
hole to remove piston and piston boot.
CAUTION:
Do not get your fingers caught in piston.
1.
Brake hose
2.
Copper washer
3.
Cap
4.
Bleed valve
5.
Sliding pin bolt
6.
Cylinder body
7.
Piston seal
8.
Piston
9.
Piston boot
10. Slipper
11. Sliding sleeve boot
12.
Sliding sleeve
B: Brake fluid
1: Molykote 7439 grease
2: Rubber grease
AWFIA0644GB
BRD0041D
REAR DISC BRAKE
BR-45
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
4. Using a suitable tool, remove piston seal from cylinder body as
shown.
CAUTION:
Be careful not to damage cylinder body inner wall.
CALIPER INSPECTION
Cylinder Body
Check inside surface of cylinder body for score, rust wear, damage or foreign materials. If any of the above
conditions are observed, replace cylinder body.
Minor damage from rust or foreign materials may be eliminated by polishing surface with a fine emery paper.
Replace cylinder body if necessary.
CAUTION:
• Use new brake fluid to clean. Do not use mineral oils such as gasoline or kerosene.
Torque Member
Check for wear, cracks, and damage. If damage or deformation is present, replace the affected part.
Piston
Check piston for score, rust, wear, damage or presence of foreign materials. Replace if any of the above con-
ditions are observed.
CAUTION:
• Piston sliding surface is plated, do not polish with emery paper even if rust of foreign materials are
stuck to sliding surface.
Sliding Pin Bolts and Sliding Pin Boots
Make sure there is no wear, damage, or cracks in sliding sleeve and sliding sleeve boots, and if there are,
replace them.
ASSEMBLY
CAUTION:
Do not use NISSAN Rubber Grease (KRE00 00010, KRE00 00010 01) when assembling.
1. Install beeld valve and cap.
2. Apply rubber grease to new piston seal (1) and insert the new
piston seal (1) in to groove on cylinder body.
CAUTION:
Do not reuse piston seal.
PFIA0269E
JPFIA0039ZZ
BR-46
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DISC BRAKE
3. Apply rubber grease to the new piston boot (2). Cover the piston
end (1) with the piston boot (2), and then install the cylinder side
lip on the piston boot (2) securley into the groove on the cylinder
body.
CAUTION:
• Do not reuse piston boot.
• Press piston evenly and vary the pressing point to pre-
vent cylinder body inner wall from being rubbed.
4. Install the piston (1) into the cylinder body and insert the piston
boot (2) side lip into piston grooves as shown.
CAUTION:
Press piston evenly and vary the pressing point to prevent
cylinder body inner wall from being rubbed.
5. Apply rubber grease to sliding sleeves, then install sliding boots and sleeves to cylinder body.
JPFIA0041ZZ
JPFIA0041ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст