Nissan Titan A60. Manual — part 737
MWI-62
< ECU DIAGNOSIS INFORMATION >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
NOTE:
The tail lamp turns OFF when the ignition switch is turned ON.
FRONT WIPER CONTROL
IPDM E/R detects front wiper stop position by a front wiper auto stop signal.
When a front wiper auto stop signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 second activation and 20 second stop five times.
NOTE:
This operation status can be confirmed on the IPDM E/R “DATA MONITOR” that displays “Block” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index
INFOID:0000000006709552
NOTE:
The details of TIME display are as follows.
• CRNT: The malfunctions that are detected now
• 1 - 39: The number is indicated when it is normal at present and a malfunction was detected in the past. It
increases like 0
→ 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF → ON. It is
fixed to 39 until the self-diagnosis results are erased if it is over 39. It returns to 0 when a malfunction is
detected again in the process.
Front wiper
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-
safe control is activated while the front wiper is set in the INT mode and the front wiper
motor is operating.
Rear window defogger (if equipped)
Rear window defogger relay OFF
A/C compressor
A/C relay OFF
Front fog lamps (if equipped)
Front fog lamp relay OFF
Control part
Fail-safe in operation
Ignition switch
Ignition relay
Tail lamp relay
ON
ON
—
OFF
OFF
—
Ignition switch
Front wiper switch
Auto stop signal
ON
OFF
Front wiper stop position signal cannot be
input 10 seconds.
ON
The signal does not change for 10 seconds.
CONSULT-III display
Fail-safe
TIME
NOTE
Refer to
No DTC is detected.
further testing
may be required.
—
—
—
—
U1000: CAN COMM CIRCUIT
×
CRNT
1 – 39
MWI
COMPASS
MWI-63
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
WIRING DIAGRAM
COMPASS
Wiring Diagram
INFOID:0000000006467136
ABNWA1014GB
MWI-64
< WIRING DIAGRAM >
COMPASS
ABNIA1811GB
MWI
METER
MWI-65
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER
Wiring Diagram
INFOID:0000000006467176
ABNWA1015GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст