Nissan Titan A60. Manual — part 803
PWC-116
< REMOVAL AND INSTALLATION >
FRONT POWER WINDOW SWITCH
FRONT POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000006161132
REMOVAL
1. Remove the power window and door lock/unlock switch finisher
(2) from the front door finisher RH. Refer to
: Pawl
2. Remove the power window and door lock/unlock switch (1) from
the power window and door lock/unlock switch finisher (2) by
releasing the tabs using suitable tool (A).
CAUTION:
Wrap a cloth around suitable tools to protect components
from damage.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA0857ZZ
REAR POWER WINDOW SWITCH
PWC-117
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Removal and Installation - Rear Door Switch
INFOID:0000000006161133
REMOVAL
1. Remove the rear power window switch finisher (1) from the rear
door finisher. Refer to
INT-10, "Removal and Installation"
.
2. Remove the rear power window switch (2) from the power win-
dow switch finisher (1) by releasing the tabs using suitable tool
(A).
CAUTION:
Wrap a cloth around suitable tools to protect components
from damage.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - Power Drop Glass Switch
INFOID:0000000006161134
REMOVAL
1. Using a suitable tool (A) release the pawls and remove the over-
head console switch finisher (1) from overhead console.
: Pawl
2. Using same tool (A) release the tabs and remove power drop
glass switch from the overhead console switch finisher (1).
CAUTION:
Wrap a cloth around suitable tools to protect components
from damage.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA0860ZZ
ALKIA1936ZZ
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
PWO-2
< PRECAUTION >
POWER SOCKET
PRECAUTION
POWER SOCKET
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006164854
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Work
INFOID:0000000006732465
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст