Nissan Titan A60. Manual — part 457
DRIVE BELTS
EM-13
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PERIODIC MAINTENANCE
DRIVE BELTS
Checking Drive Belts
INFOID:0000000006179379
WARNING:
Be sure to perform when the engine is stopped.
1. Remove air duct and resonator assembly when inspecting drive belt.
2. Make sure that indicator (single line notch) of each auto tensioner is within the allowable working range
(between three line notches).
NOTE:
• Check the drive belt auto tensioner indication when the engine is cold.
• The indicator notch is located on the moving side of the drive belt auto tensioner.
3. Visually check entire belt for wear, damage or cracks.
4. If the indicator is out of allowable working range or belt is damaged, replace the belt. Refer to
DRIVE BELT TENSION
There is no manual drive belt tension adjustment. The drive belt tension is automatically adjusted by the drive
belt auto tensioner.
Removal and Installation
INFOID:0000000006179380
REMOVAL
1. Remove the air duct and resonator assembly. Refer to
EM-25, "Removal and Installation"
1.
Drive belt
2.
Power steering pump pulley
3.
Generator pulley
4.
Crankshaft pulley
5.
A/C compressor
6.
Idler pulley
7.
Cooling fan pulley
8.
Water pump pulley
9.
Drive belt auto tensioner
A.
Allowable working range
LBIA0391E
EM-14
< PERIODIC MAINTENANCE >
DRIVE BELTS
2. Install Tool on drive belt auto tensioner pulley bolt, move in the
direction of arrow (loosening direction of tensioner) as shown.
WARNING:
Avoid placing hand in a location where pinching may occur
if the holding tool accidentally comes off.
3. Remove the drive belt.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure belt is securely installed around all pulleys.
• Rotate the crankshaft pulley several turns clockwise to equalize belt tension between pulleys.
• Make sure belt tension is within the allowable working range, using the indicator notch on the drive belt auto
tensioner. Refer to
.
Drive Belt Auto Tensioner and Idler Pulley
INFOID:0000000006179381
REMOVAL
1. Remove the drive belt. Refer to
EM-13, "Removal and Installation"
.
2. Remove the drive belt auto tensioner and idler pulley using power tool.
INSTALLATION
Installation is in the reverse order of removal.
Tool number
: — (J-46535)
WBIA0537E
AWBIA0975ZZ
1.
Drive belt auto tensioner
2.
Idler pulley
AIR CLEANER FILTER
EM-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER FILTER
Exploded View
INFOID:0000000006179382
Removal and Installation (Viscous paper type)
INFOID:0000000006179383
REMOVAL
NOTE:
• The viscous paper type filter does not need cleaning between replacement intervals.
• Replace the air filter as necessary for periodic maintenance. Refer to
MA-9, "FOR NORTH AMERICA : Intro-
duction of Periodic Maintenance"
, (United States and Canada),
MA-13, "FOR MEXICO : Introduction of Peri-
(Mexico).
1. Remove the air cleaner case (upper).
2. Remove the air cleaner filter from the air cleaner case (lower).
INSTALLATION
1. Install the new air cleaner filter in the air cleaner case (lower).
2. Install the air cleaner case (upper).
1.
Air cleaner case (lower)
2.
Air cleaner filter
3.
Air cleaner case (upper)
4.
Air duct and resonator assembly
Front
ALBIA0413GB
EM-16
< PERIODIC MAINTENANCE >
SPARK PLUG
SPARK PLUG
Exploded View
INFOID:0000000006179384
Removal and Installation
INFOID:0000000006179385
REMOVAL
1. Remove ignition coil. Refer to
EM-38, "Removal and Installation"
.
CAUTION:
Do not shock ignition coil.
2. Remove spark plug using suitable tool.
CAUTION:
Do not drop or shock spark plug.
INSPECTION AFTER REMOVAL
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be used.
1.
Ignition coil
2.
Spark plug
WBIA0796E
SEM294A
Cleaner air pressure:
Less than 588 kPa (6 kg/cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст