Nissan Titan A60. Manual — part 995
TPMS
WT-9
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
A sensor-transmitter integrated with a valve is installed in each
wheel, and transmits a detected air pressure signal in the form of a
radio wave. The radio signal is received by the remote keyless entry
receiver.
REMOTE KEYLESS ENTRY RECEIVER
The remote keyless entry receiver is shown with the instrument
panel RH removed. The remote keyless entry receiver receives the
air pressure signal transmitted by the transmitter in each wheel.
COMBINATION METER
The combination meter receives tire pressure status from the BCM
using CAN communication. When a low tire pressure condition is
sensed by the BCM, the combination meter low tire pressure warn-
ing lamp is activated. A CHECK TIRE PRESSURE warning mes-
sage will also be displayed in the vehicle information display. Refer
to the Owner’s Manual for additional information.
TIRE PRESSURE WARNING CHECK CONNECTOR
The tire pressure warning check connector can be grounded in order
to initiate self-diagnosis without CONSULT-III. Refer to
Diagnosis (Without CONSULT-III)"
. The tire pressure warning check
connector is located behind the lower portion of the instrument panel
LH.
DISPLAY UNIT (with NAVI)
WEIA0137E
LEIA0069E
LEIA0055E
LEIA0068E
WT-10
< SYSTEM DESCRIPTION >
TPMS
Displays the air pressure of each tire.
NOTE:
After the ignition switch is turned on, the pressure values will not be
displayed until the data of each wheel is received.
System Component
INFOID:0000000006179282
WEIA0162E
AWEIA0007ZZ
1.
Display control unit M95
(with NAVI)
2.
Tire pressure warning check connec-
tor
M123
3.
Transmitter
4.
BCM
M18, M20
5.
Combination meter
M24
6.
Display unit M93
(with NAVI)
7.
Remote keyless entry receiver
M120
DIAGNOSIS SYSTEM (BCM)
WT-11
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006752634
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
CONSULT-III Function (BCM - AIR PRESSURE MONITOR)
INFOID:0000000006752635
SELF DIAGNOSTIC RESULT
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
Ecu Id
en
tificati
on
Sel
f Di
agn
os
tic Re
su
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
ork
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN Diag S
upport Mntr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
Air conditioner
AIR CONDITIONER
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Panic alarm system
PANIC ALARM
×
WT-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
NOTE:
Before performing Self Diagnostic Result, be sure to register the ID, or else the actual malfunction may be dif-
ferent from that displayed on CONSULT-III.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Self-Diagnosis (Without CONSULT-III)
INFOID:0000000006179284
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III)
1. Turn ignition switch ON.
2. Ground the tire pressure warning check connector to initiate self diagnosis.
3. Compare the flashing pattern with the flash code chart below.
NOTE:
Monitor Item
Condition
Specification
VEHICLE SPEED
Drive vehicle
Vehicle speed (km/h or mph)
AIR PRESS FL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool is trans-
mitting activation signals.
Tire pressure (kPa, kg/cm
2
or psi).
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
ID REGST FL1
Ignition switch ON.
Registration ID: Green.
No registration: Red.
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
Ignition switch ON.
Low tire pressure warning lamp on: ON.
Low tire pressure warning lamp off: OFF.
BUZZER
Ignition switch ON.
Buzzer in combination meter on: ON.
Buzzer in combination meter off: OFF.
Test Item
Description
WARNING LAMP
This test is able to check tire pressure warning lamp operation [Off/On].
ID REGIST WARNING
This test is able to check ID regist warning chime operation [Off/On].
FLAT TIRE WARNING
This test is able to check flat tire warning chime operation [Off/On].
HORN
This test is able to check horn operation [On].
FLASHER
This test is able to check turn signal lamp operation [Off/LH/RH].
Support Item
Description
ID REGIST
WT-6, "ID Registration Procedure"
ID READ
The registered ID number is displayed.
ALEIA0050GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст