Nissan Titan A60. Manual — part 25

ADP-90

< DTC/CIRCUIT DIAGNOSIS >

MIRROR SENSOR

1. Turn ignition switch OFF.

2. Disconnect automatic drive positioner control unit and door mir-

ror LH connector.

3. Check continuity between automatic drive positioner control unit

harness connector and door mirror LH harness connector.

4. Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR LH SENSOR CIRCUIT 2

1. Check continuity between automatic drive positioner control unit

harness connector and door mirror LH harness connector.

2. Check continuity between automatic drive positioner control unit

harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK PEDAL ADJUSTING OPERATION

1. Connect driver seat control unit connector and door mirror LH connector.

2. Turn ignition switch ON.

3. Check pedal adjusting operation with memory function.
Is the operation normal?

YES

>> Replace door mirror actuator LH. Refer to

MIR-18, "Mirror Actuator"

.

NO

>> Replace automatic drive positioner control unit. Refer to

ADP-149, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-149, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning part.

Automatic drive

positioner control

unit connector

Terminal

Door mirror LH

connector

Terminal

Continuity

M33

6

D4

7

Yes

22

8

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity

M33

6

No

22

LIIA1484E

Automatic drive

positioner control

unit connector

Terminal

Door mirror LH

connector

Terminal

Continuity

M34

33

D4

5

Yes

41

6

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity

M34

33

No

41

LIIA1483E

MIRROR SENSOR

ADP-91

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

PASSENGER SIDE
PASSENGER SIDE : Description

INFOID:0000000006163550

• The mirror sensor RH is installed to the door mirror RH.

• The resistance of 2 sensors (horizontal and vertical) is changed when the door mirror RH is operated.

• Automatic drive positioner control unit calculates the door mirror position according to the change of the volt-

age of 2 sensor input terminals.

PASSENGER SIDE : Component Function Check

INFOID:0000000006163551

1.

CHECK FUNCTION

1. Select “MIR/SEN RH U-D”, “MIR/SEN RH R-L” in “Data monitor” with CONSULT-III.

2. Check the mirror sensor RH signal under the following conditions.

Is the indication normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to

ADP-91, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006163552

Regarding Wiring Diagram information, refer to

ADP-128, "Wiring Diagram"

.

1.

CHECK DOOR MIRROR RH SENSOR SIGNAL

1. Turn ignition switch to ACC.

2. Check voltage between door mirror RH harness connector and

ground.

Is the inspection result normal?

YES

>> GO TO 5

NO

>> GO TO 2

2.

CHECK DOOR MIRROR RH SENSOR HARNESS CONTINUITY

Monitor item

Condition

Value

MIR/SEN RH U-D

Door mirror RH

Close to peak

3.4V

Close to valley

0.6V

MIR/SEN RH R-L

Close to right edge

3.4V

Close to left edge

0.6V

Terminals

Condition

Voltage (V)

(Approx.)

(+)

(–)

Door mirror

RH con-

nector

Terminal

D107

7

Ground

Door mirror
RH

Close to peak

3.4

Close to valley

0.6

8

Close to right edge

3.4

Close to left edge

0.6

LIIA1485E

ADP-92

< DTC/CIRCUIT DIAGNOSIS >

MIRROR SENSOR

1. Turn ignition switch OFF.

2. Disconnect automatic drive positioner control unit and door mir-

ror RH.

3. Check continuity between automatic drive positioner control unit

harness connector and door mirror RH harness connector.

4. Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR RH SENSOR POWER SUPPLY CIRCUIT

1. Check continuity between automatic drive positioner control unit

harness connector and door mirror RH harness connector.

2. Check continuity between automatic drive positioner control unit

harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4

NO

>> Repair or replace harness.

4.

CHECK PEDAL ADJUSTING OPERATION

1. Connect driver seat control unit connector and door mirror RH connector.

2. Turn ignition switch ON.

3. Check pedal adjusting operation with memory function.
Is the operation normal?

YES

>> Replace door mirror actuator. Refer to

MIR-18, "Mirror Actuator"

.

NO

>> Replace automatic drive positioner control unit. Refer to

ADP-149, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-149, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning part.

Automatic drive posi-

tioner control unit

connector

Terminal

Door mirror RH

connector

Terminal

Continuity

M33

5

D107

7

Yes

21

8

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity

M33

5

No

21

LIIA1473E

Automatic drive posi-

tioner control unit

connector

Terminal

Door mirror RH

connector

Terminal

Continuity

M34

33

D107

5

Yes

41

6

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity

M34

33

No

41

LIIA1486E

SLIDING MOTOR

ADP-93

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SLIDING MOTOR

Description

INFOID:0000000006163553

• The sliding motor LH is installed to the power seat frame assembly.

• The sliding motor LH is installed with the driver seat control unit.

• The seat is slid forward/backward by changing the rotation direction of sliding motor LH.

Component Function Check

INFOID:0000000006163554

1.

CHECK FUNCTION

1. Select “SEAT SLIDE” in “Active test” mode with CONSULT-III.

2. Check the sliding motor LH operation.

Is the operation of relevant parts normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to

ADP-93, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006163555

Regarding Wiring Diagram information, refer to

ADP-128, "Wiring Diagram"

.

1.

CHECK SLIDING MOTOR LH POWER SUPPLY

1. Turn the ignition switch OFF.

2. Perform “Active test” (“SEAT SLIDE”) with CONSULT-lll

3. Check voltage between driver seat control unit harness connec-

tor and ground.

Is the inspection result normal?

YES

>> Replace sliding motor LH. (Built in power seat frame assembly). Refer to

SE-44, "Disassembly

and Assembly"

.

NO

>> GO TO 2

2.

CHECK SLIDING MOTOR LH CIRCUIT

Test Item

Description

SEAT SLIDE

OFF

Seat sliding

Stop

FR

Forward

RR

Backward

Terminal

Test Item

Voltage (V)

(Approx.)

(+)

(-)

Driver seat
control unit

connector

Terminal

B203

35

Ground

SEAT

SLIDE

OFF

0

FR (forward)

Battery voltage

RR (backward)

0

42

OFF

0

FR (forward)

0

RR (backward) Battery voltage

PIIA4801E