Nissan Titan A60. Manual — part 161
BRC-22
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
EBD
Component Parts Location
INFOID:0000000006648970
1.
Front wheel sensor LH E18
Front wheel sensor RH E117
2.
Delta stroke sensor E114
3.
Active booster E49
4.
Front pressure sensor E31
5.
Rear pressure sensor E32
6.
Brake fluid level switch E21
7.
ABS actuator and electric unit (con-
trol unit) E125
8.
Combination meter M24
9.
Steering angle sensor M17 (view
with steering wheel removed)
AWFIA0740ZZ
EBD
BRC-23
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Component Description
INFOID:0000000006648971
10. Yaw rate/side/decel G sensor M108 11. Rear wheel sensor LH C11
Rear wheel sensor RH C10
12. VDC OFF switch M148
13. Stop lamp switch E38 (column shift),
E42 (floor shift)
14. Stop lamp relay E12
Component parts
Reference
ABS actuator and electric unit (control unit)
Pump
Motor
Actuator relay
Solenoid valve
VDC switch-over valve
(CV1, CV2, SV1, SV2)
Wheel sensor
Yaw rate/side/decel G sensor
Stop lamp switch
Front pressure sensor
Rear pressure sensor
Steering angle sensor
Brake fluid level switch
Active booster
Delta stroke sensor
VDC OFF switch
ABS warning lamp
Brake warning lamp
VDC OFF indicator lamp
SLIP indicator lamp
BRC-24
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III Function (ABS)
INFOID:0000000006165828
FUNCTION
CONSULT-III can display each diagnostic item using the following direct diagnostic modes.
SELF DIAGNOSTIC RESULT
Operation Procedure
1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How to Erase Self-diagnostic Result
1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately
1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp,
VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the
system is normal unless the vehicle is driving at approximately 30 km/h (19 MPH) or more for approxi-
mately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid
level switch operation (when brake fluid is insufficient).
• VDC OFF switch should not stay “ON” position.
Display Item List
DATA MONITOR
Direct Diagnostic Mode
Description
ECU Identification
The ABS actuator and electric unit (control unit) part number is displayed.
Self Diagnostic Result
The ABS actuator and electric unit (control unit) self diagnostic results are displayed.
Data Monitor
The ABS actuator and electric unit (control unit) input/output data is displayed in real time.
Active Test
The ABS actuator and electric unit (control unit) activates outputs to test components.
Function Test
This mode displays self diagnostic results of ABS system with either an “OK” or “NG”.
Work support
The settings for ABS actuator and electric unit (control unit) functions can be changed.
CAN Diag Support Monitor
The result of transmit/receive diagnosis of CAN communication is diplayed.
Item
(Unit)
Data monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
FR LH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by front LH
wheel sensor signal is displayed.
FR RH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by front RH
wheel sensor signal is displayed.
RR LH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by rear LH
wheel sensor signal is displayed.
RR RH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by rear RH
wheel sensor signal is displayed.
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-25
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
DECEL G-SEN
(G)
×
×
×
Longitudinal acceleration (G) detected by decel G-
sensor is displayed.
FR RH IN SOL
(On/Off)
–
×
×
Front RH IN ABS solenoid (On/Off) status is dis-
played.
FR RH OUT SOL
(On/Off)
–
×
×
Front RH OUT ABS solenoid (On/Off) status is dis-
played.
FR LH IN SOL
(On/Off)
–
×
×
Front LH IN ABS solenoid (On/Off) status is displayed.
FR LH OUT SOL
(On/Off)
–
×
×
Front LH OUT ABS solenoid (On/Off) status is dis-
played.
RR RH IN SOL
(On/Off)
–
×
×
Rear RH IN ABS solenoid (On/Off) status is displayed.
RR RH OUT SOL
(On/Off)
–
×
×
Rear RH OUT ABS solenoid (On/Off) status is dis-
played.
RR LH IN SOL
(On/Off)
–
×
×
Rear LH IN ABS solenoid (On/Off) status is displayed.
RR LH OUT SOL
(On/Off)
–
×
×
Rear LH OUT ABS solenoid (On/Off) status is dis-
played.
EBD WARN LAMP
(On/Off)
–
–
×
Brake warning lamp (On/Off) status is displayed.
STOP LAMP SW
(On/Off)
×
×
×
Stop lamp switch (On/Off) status is displayed.
MOTOR RELAY
(On/Off)
–
×
×
ABS motor relay signal (On/Off) status is displayed.
ACTUATOR RLY
(On/Off)
–
×
×
ABS actuator relay signal (On/Off) status is displayed.
ABS WARN LAMP
(On/Off)
–
×
×
ABS warning lamp (On/Off) status is displayed.
OFF LAMP
(On/Off)
–
×
×
VDC OFF Lamp (On/Off) status is displayed.
OFF SW
(On/Off)
×
×
×
VDC OFF switch (On/Off) status is displayed.
SLIP LAMP
(On/Off)
–
×
×
SLIP indicator lamp (On/Off) status is displayed.
BATTERY VOLT
(V)
×
×
×
Voltage (V) supplied to ABS actuator and electric unit
(control unit) is displayed.
GEAR
(1, 2, 3, 4, 5)
×
×
×
Gear position (1, 2, 3, 4, 5) judged by transmission
range switch signal is displayed.
SLCT LVR POSI
(P, N, D)
×
×
×
Shift position (P, N, D) judged by transmission range
switch signal.
ENGINE SPEED
(rpm)
×
×
×
Engine speed (rpm) judged by CAN communication
signal is displayed.
YAW RATE SEN
(d/s)
×
×
×
Yaw rate (d/s) detected by yaw rate sensor is dis-
played.
R POSI SIG
(On/Off)
–
–
×
Reverse shift position (On/Off) judged by transmis-
sion range switch signal.
4WD FAIL REQ
(On/Off)
–
–
×
Transfer control unit fail-safe mode (On/Off) is dis-
played.
N POSI SIG
(On/Off)
–
–
×
Shift position judged by transmission range switch
signal.
Item
(Unit)
Data monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст