Nissan Titan A60. Manual — part 972
TM-276
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
d. Calculate dimension “M”.
3. Adjust total end play “T
1
”.
• Select proper thickness of bearing race so that total end play
is within specifications.
Assembly (2)
INFOID:0000000006159473
1. Install O-ring to oil pump assembly.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
2. Install bearing race to oil pump assembly.
CAUTION:
Apply petroleum jelly to bearing race.
“M”: Distance between transmission case fitting sur-
face of oil pump and needle bearing on oil pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
” : 0.25 - 0.55 mm (0.0098 - 0.0217 in)
Bearing races :Refer to
SCIA2810E
SCIA5172E
SCIA6529E
ASSEMBLY
TM-277
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump bearing.
4. Apply recommended sealant (Genuine RTV Silicone Sealant or
GI-15, "Recommended Chemical Products
.) to oil pump assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the oil pump bolts and oil pump bolt
mating surfaces.
5. Tighten oil pump bolts to specified torque.
CAUTION:
Apply ATF to oil pump bushing.
6. Install O-ring to input clutch assembly.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
7. Install converter housing to transmission case and tighten bolts
to specified torque.
CAUTION:
Do not reuse self-sealing bolt (A).
SCIA2811E
SCIA5321E
Oil pump bolts
: 48 N·m (4.9 kg-m, 35 ft-lb)
SCIA2300E
SCIA5011E
Converter housing bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt (A)
: 61 N·m (6.2 kg-m, 45 ft-lb)
WCIA0662E
TM-278
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
8. Make sure that brake band (1) does not close input speed sen-
sor hole (A).
9. Connect TCM connector (1) and transmission range switch con-
nector (2).
10. Install A/T assembly harness connector to control valve with
TCM.
11. Connect TCM connectors.
12. Install O-ring to A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
JSDIA1318ZZ
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
ASSEMBLY
TM-279
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
13. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
14. Install plug (2) to bracket (1).
15. Install plug (1) [with bracket (2)] to control valve with TCM and
tighten bolt (
) to specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
16. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
JSDIA1313ZZ
JSDIA1312ZZ
Bracket bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
JSDIA1311ZZ
1
: Brake band
JSDIA1318ZZ
SCIA5035E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст