Nissan Titan A60. Manual — part 821

    SUNROOF SYSTEM

    RF-51

    < REMOVAL AND INSTALLATION >

    C

    D

    E

    F

    G

    H

    I

    J

    L

    M

    A

    B

    RF

    N

    O

    P

    2. Install the glass lid assembly screws. (First tighten left front bolt, then tighten right rear bolt on glass lid to

    prevent lid from moving while tightening other bolts.)

    3. Adjust the glass lid assembly. Refer to

    RF-46, "Inspection"

    .

    4. Install side cover LH and RH.

    WIND DEFLECTOR

    Removal

    1. Open the sunroof.
    2. Remove screws from the left, center, and right side wind deflec-

    tor holders.

    3. Remove the wind deflector from the sunroof frame assembly.

    Installation

    Installation is in the reverse order of removal.

    SUNSHADE

    Removal

    1. Remove the headlining. Refer to

    INT-21, "Removal and Installation"

    .

    2. Loosen sunroof frame assembly bolts and remove rear sunroof frame assembly brackets.
    3. Lower rear edge of sunroof frame side rails enough for clearance from roof panel.
    4. Remove the sunshade stoppers (2 points) from the rear end of

    the sunroof frame assembly.

    5. Remove the sunshade assembly from the rear end of the sun-

    roof frame assembly.

    Installation

    Installation is in the reverse order of removal.

    SUNROOF MOTOR

    Removal

    CAUTION:

    • When removing the sunroof motor, be sure to place the link and wire assembly in the symmetrical

    and fully closed position.

    • Never run the removed motor as a single unit.
    •

    :Vehicle front

    1. Position the sunroof assembly in the fully closed position.
    2. Remove the front roof console. Refer to

    INT-21, "Removal and Installation"

    .

    LIIA1099E

    SBT251A

    RF-52

    < REMOVAL AND INSTALLATION >

    SUNROOF SYSTEM

    3. Disconnect the sunroof motor harness connector (2).
    4. Remove the sunroof motor screws (3), then remove the sunroof

    motor (1).

    Installation

    CAUTION:

    Before installing the sunroof motor assembly, be sure to place the link and wire assembly in the sym-

    metrical and fully closed position.
    •

    :Vehicle front

    1. Move the sunroof motor (1) laterally little by little so that the gear

    is completely engaged into the wire on the sunroof unit and the

    installation surface becomes parallel. Then, secure the motor

    with screws (3).

    2. Connect the wire harness connector (2) to the sunroof motor (1).
    3. Install the front roof console. Refer to

    RF-50, "Removal and

    Installation"

    .

    4. Reset the sunroof motor memory. Refer to

    RF-5, "ADDITIONAL

    SERVICE WHEN REPLACING CONTROL UNIT : Special

    Repair Requirement"

    .

    WIIA0772E

    WIIA0772E

    RSU-2

    < PRECAUTION >

    PRECAUTIONS

    PRECAUTION

    PRECAUTIONS

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
    PRE-TENSIONER"

    INFOID:0000000006161774

    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

    with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

    types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

    system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

    air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

    Information necessary to service the system safely is included in the SR and SB section of this Service Man-

    ual.

    WARNING:

    • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

    the event of a collision which would result in air bag inflation, all maintenance must be performed by

    an authorized NISSAN/INFINITI dealer.

    • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

    injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

    Module, see the SR section.

    • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

    Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

    ness connectors.

    PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

    WARNING:

    • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

    tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

    hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

    serious injury.

    • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

    battery, and wait at least 3 minutes before performing any service.

    General Precautions

    INFOID:0000000006161775

    • When installing rubber parts, final tightening must be carried out under unladen condition* with tires

    on ground.

    * Fuel, radiator coolant, and engine oil are full. Spare tire, jack, hand tools, and mats are in their des-

    ignated positions.

    Была ли эта страница вам полезна?
    Да!Нет
    2 посетителя считают эту страницу полезной.
    Большое спасибо!
    Ваше мнение очень важно для нас.

    Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

    Текст

    Матвей Александрович30.05.2024 02:07
    Политика конфиденциальности