Nissan Titan A60. Manual — part 534
WHEEL HUB
FAX-7
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
8. Remove splash guard and wheel hub and bearing assembly from steering knuckle.
INSPECTION AFTER REMOVAL
Check for deformity, cracks and damage on each part, replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
• Use new bolts when installing the wheel hub and bearing assembly.
• Tighten drive shaft nut to specification.Refer to
FAX-8, "Removal and Installation"
.
• When installing disc rotor on wheel hub and bearing assembly,
position the disc rotor according to alignment mark.
(When not using the alignment mark, refer to
and Installation of Brake Caliper and Rotor"
.)
• When installing wheel and tire. Refer to
WDIA0044E
FAX-8
< UNIT REMOVAL AND INSTALLATION >
DRIVE SHAFT
DRIVE SHAFT
Removal and Installation
INFOID:0000000006161625
REMOVAL
1. Remove wheel and tire using power tool.
2. Remove engine under cover using power tool.
3. Remove wheel sensor harness from mount on knuckle.
CAUTION:
Do not pull on wheel sensor harness.
4. Without disassembling the hydraulic lines, remove brake caliper using power tool. Reposition it aside with
wire. Refer to
BR-32, "Removal and Installation of Brake Caliper and Rotor"
.
NOTE:
Avoid depressing brake pedal while brake caliper is removed.
5. Remove coil spring and shock absorber assembly using power tool. Refer to
.
6. Separate upper link ball joint stud from steering knuckle using
Tool.
• Support lower link with jack.
7. Remove cotter pin, then remove drive shaft nut.
8. Remove drive shaft bolts from front final drive.
9. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:
• When removing drive shaft, do not apply an excessive
angle to drive shaft joint. Also be careful not to exces-
sively extend slide joint.
INSPECTION AFTER REMOVAL
• Move joint up, down, left, right, and in axial direction. Check for any rough movement or significant loose-
ness.
• Check boot for cracks or other damage, and for grease leakage.
• If damaged, disassemble drive shaft to verify damage, and repair
or replace as necessary.
1.
Cotter pin
2.
Drive shaft nut
3.
Drive shaft
WDIA0329E
Tool number
: ST29020001 (J-24319-01)
LEIA0095E
RAA0030D
DRIVE SHAFT
FAX-9
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
• Tighten wheel nuts to specification. Refer to
FAX-10
< UNIT DISASSEMBLY AND ASSEMBLY >
DRIVE SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
DRIVE SHAFT
Disassembly and Assembly
INFOID:0000000006161626
DISASSEMBLY
Final Drive Side
1. Mount the drive shaft in a vise.
CAUTION:
When mounting the drive shaft in a vise, use copper or aluminum plates between the vise and the
drive shaft.
2. Remove the boot bands.
3. Remove the stopper ring with suitable tool as shown, and pull
the housing off.
1. Sliding joint housing
2. Snap ring
3. Ball cage, steel ball, inner race assembly
4. Stopper ring
5. Boot band
6. Boot
7. Drive shaft
8. Circlip
9. Joint sub-assembly
WDIA0054E
SRA249A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст