Nissan Titan A60. Manual — part 826
SEAT BELTS
SB-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Removal - King Cab
CAUTION:
Before servicing the SRS, turn the ignition switch off, disconnect the battery terminals nad wait at
least three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove D-ring anchor bolt cover and bolt.
3. Remove anchor cover and bolt.
4. Remove lower door finisher.
5. Disconnect seat belt pre-tensioner connector.
6. Remove seat belt retractor and belt assembly.
Installation - King Cab
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF SEAT BELT BUCKLE
Removal - Bucket Seat
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove the front seat. Refer to
SE-30, "Removal and Installation For Front Seat"
.
3. Remove screw and seat cushion inner finisher.
4. Remove the anchor bolt and buckle.
5. Disconnect the buckle switch connector from the seat connector.
Installation - Bucket Seat
CAUTION:
• Passenger seat is equipped with Occupant Classification System sensor and control module. Do not
disassemble front passenger seat cushion assembly or remove trim as this will affect the Occupant
Classification System calibration.
• On passenger seat during installation, the wire harness clips must be installed in the holes they were
originally in.
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF CENTER BENCH SEAT BELT AND SEAT BELT BUCKLE
WHIA0128E
SB-8
< REMOVAL AND INSTALLATION >
SEAT BELTS
Removal
1. Remove center front seat. Refer to
SE-30, "Removal and Installation For Front Seat"
2. Remove anchor bolt cover, bolt and seat belt.
3. Remove anchor bolt cover, bolt and seat belt buckle.
Installation
Installation is in the reverse order of removal.
1.
Center front seat
2.
Seat belt anchor bolts
3.
Anchor bolt covers
4.
Seat belt assembly
5.
Seat belt buckle
WIIA0993E
SEAT BELTS
SB-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Removal and Installation of Rear Seat Belt
INFOID:0000000006158504
REMOVAL
1. Remove rear kicking plates. Refer to
INT-14, "Removal and Installation"
2. Remove rear seat assembly. Refer to
SE-36, "Removal and Installation"
.
3. Remove seat belt D-ring anchor bolt cover and bolt.
4. Remove seat belt lower anchor cover and bolt.
1.
D-ring anchor bolt cover
2.
D-ring anchor
3.
Seat belt retractor and belt assembly
RH
4.
Seat belt pre-tensioner connector
5.
Lower side finisher
6.
Seat belt lower anchor
7.
Seat belt lower anchor cover
8.
Push pins
9.
Center anchor bracket cover
10. Center seat belt retractor and belt as-
sembly
11. Seat belt buckles
12. Center seat belt anchor bracket
13. Seat belt retractor and belt assembly
LH
AWHIA0264GB
SB-10
< REMOVAL AND INSTALLATION >
SEAT BELTS
5. Remove lower side finisher. Refer to
INT-14, "Removal and Installation"
.
6. Remove seat belt retractor anchor bolt and the seat belt assembly.
7. Remove center seat belt lower anchor bolt.
8. Remove center seat belt retractor.
9. Remove center anchor bracket cover.
10. Remove push pins from center seat belt webbing sleeve.
11. Remove bolts from anchor bracket and remove center seat belt retractor and belt assembly.
12. Remove center belt bracket from floor.
13. Remove seat belt buckles.
INSTALLATION
Installation is in the reverse order of removal.
• Attach rear center seat belt retractor anchor bracket bolts before seat installation.
• Attach rear center seat belt retractor anchor bolt after seat installation with the seat cushion raised.
Seat Belt Inspection
INFOID:0000000006158505
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
• The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
• The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
PRELIMINARY CHECKS
1. Check the seat belt warning lamp/chime for proper operation as follows:
a. Switch ignition ON. The seat belt warning lamp should illuminate. Also, the seat belt warning chime should
sound for about seven seconds.
b. Fasten drivers seat belt. The seat belt warning lamp should go out and the chime (if sounding) should
stop.
2. If the air bag warning lamp is blinking, conduct self-diagnosis using CONSULT-III, and air bag warning
lamp. Refer to
.
3. Check that the seat belt retractor, seat belt anchor and buckle bolts are securely attached.
4. Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swivels
freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly and
holds securely.
5. Check retractor operation:
a. Fully extend the seat belt webbing and check for twists, tears or other damage.
b. Allow the seat belt to retract. Ensure that belt returns smoothly and completely into the retractor. If the
seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth, because dirt built
up in the loops of the upper anchors can cause the seat belts to retract slowly.
c.
Fasten the seat belt. Check the seat belt returns smoothly and completely to the retractor. If the belt does
not return smoothly, the cause may be an accumulation of dust or dirt. Use the “SEAT BELT TAPE SET”
and perform the following steps.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст