Nissan Titan A60. Manual — part 463
OIL PAN AND OIL STRAINER
EM-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Check engine oil level again.
EM-38
< REMOVAL AND INSTALLATION >
IGNITION COIL
IGNITION COIL
Exploded View
INFOID:0000000006179397
Removal and Installation
INFOID:0000000006179398
REMOVAL
1. Remove the engine room cover. Refer to
EM-24, "Removal and Installation"
2. Disconnect the harness connector from the ignition coil.
3. Remove the ignition coil.
CAUTION:
Do not shock ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
WBIA0796E
ROCKER COVER
EM-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ROCKER COVER
Exploded View
INFOID:0000000006179399
Removal and Installation
INFOID:0000000006179400
REMOVAL
1. Remove the engine room cover, if equipped. Refer to
EM-24, "Removal and Installation"
.
2. Move the harness on the upper rocker cover and its peripheral aside.
3. Remove the ignition coils. Refer to
EM-38, "Removal and Installation"
.
4. Disconnect crankcase ventilation hoses from rocker covers.
5. Remove the PCV hose from the PCV control valves.
6. Loosen the rocker cover bolts in reverse order as shown using
power tool.
CAUTION:
Do not hold the rocker cover (RH) (B) by the oil filler neck.
•
: Engine front
• A: Rocker cover LH
• B: Rocker cover RH
7. Remove the rocker cover.
INSTALLATION
1.
Rocker cover (LH)
2.
PCV control valve
3.
O-ring
4.
Rocker cover gasket (LH)
5.
Rocker cover (RH)
6.
PCV control valve
7.
O-ring
8.
Oil filler cap
9.
Rocker cover gasket (RH)
KBIA2508E
WBIA0697E
EM-40
< REMOVAL AND INSTALLATION >
ROCKER COVER
1. Apply liquid gasket to the joint part of the cylinder head and
camshaft bracket following the steps below.
NOTE:
Illustration shows an example of (LH) side (zoomed in shows
No.1 camshaft bracket).
a. Use illustration
″a″ to apply liquid gasket to the joint part of No.1
camshaft bracket and cylinder head.
b. Use illustration
″b″ to apply liquid gasket 90° to illustration ″a″.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
2. Install the rocker cover and tighten the bolts in two steps in the
order shown.
• A: Rocker cover LH
• B: Rocker cover RH
•
: Engine front
CAUTION:
• Do not hold the rocker cover (RH) (B) by the oil filler neck.
• Make sure the new rocker cover gasket is installed in the
groove of the rocker cover.
3. Install the PCV hoses.
NOTE:
• Remove foreign materials from inside the hose using compressed air.
• The inserted length is within 25 - 30 mm (0.98 - 1.18 in) [Target: 25 mm (0.98 in)].
4. Installation of the remaining components is in the reverse order of removal.
Tool number
: WS39930000 ( — )
KBIA2510E
1st step
: 2.0 N·m (0.2 kg-m, 18 in-lb)
2nd step
: 8.3 N·m (0.85 kg-m, 73 in-lb)
WBIA0697E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст