Nissan Titan A60. Manual — part 857
SEC-66
< SYMPTOM DIAGNOSIS >
VEHICLE SECURITY SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
VEHICLE SECURITY SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000006161614
*: Check the system is in the armed phase.
Procedure
Diagnostic procedure
Refer to page
Symptom
1
Vehicle security sys-
tem cannot be set by
····
Door switch
Check door switch (king cab)
Check door switch (crew cab)
Key cylinder switch
Check key cylinder switch (king cab)
Check key cylinder switch (crew cab)
—
Check Intermittent Incident
Security indicator does not turn ON.
Check vehicle security indicator
Check Intermittent Incident
2
* Vehicle security
system does not
sound alarm when ····
Any door is opened.
Check door switch (king cab)
Check door switch (crew cab)
—
Check Intermittent Incident
3
Vehicle security
alarm does not acti-
vate.
Horn alarm
Check horn switch
—
Check Intermittent Incident
4
Vehicle security sys-
tem cannot be can-
celed by ····
Key cylinder switch
Check key cylinder switch (king cab)
Check key cylinder switch (crew cab)
—
Check Intermittent Incident
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS SYMPTOMS
SEC-67
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS SYMPTOMS
Symptom Table
INFOID:0000000006161615
NOTE:
• Before performing the diagnosis in the following table, check “
”.
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
• Ignition switch is not turned ON.
• Ignition key is not inserted into key cylinder.
Symptom
Diagnosis/service procedure
Reference page
Security indicator does not turn ON or flash.
1. Check vehicle security indicator
2. Check Intermittent Incident
SEC-68
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006161616
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
NATS ANTENNA AMP.
SEC-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000006752629
NATS ANTENNA AMP
NOTE:
• If NATS antenna amp. is not installed correctly, NVIS (NATS) system will not operate properly and "SELF-
DIAG RESULTS" on CONSULT -III screen will show "LOCK MODE" or "CHAIN OF IMMU-KEY"
• Initialization is not necessary when only the NATS antenna amp. is replaced with a new one.
Removal
1. Disconnect the battery negative terminal.
2. Remove cluster lid A. Refer to
IP-13, "Removal and Installation"
3. Remove the bolt (A), disconnect the electrical connector (1), and
remove the NATS antenna amp (2).
Installation
Installation is in the reverse order of removal.
ALKIA1858GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст