Nissan Titan A60. Manual — part 136
BCS-24
< SYSTEM DESCRIPTION >
[BCM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
WORK SUPPORT
*: Initial setting
RETAINED PWR
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR)
INFOID:0000000006161335
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
*: Initial setting
SIGNAL BUFFER
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH.
KEY CYL LK-SW [On/Off]
Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off]
Indicates condition of unlock signal from door key cylinder switch.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off]
Indicates condition of unlock signal from door lock and unlock switch.
Monitor Item [Unit]
Description
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation [Off/On].
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation [On].
HEADLAMP(HI)
This test is able to check vehicle security lamp operation [On].
Support Item
Setting
Description
SECURITY ALARM SET
Off
Security alarm OFF.
On*
Security alarm ON.
THEFT ALM TRG
Off/On
The switch which triggered vehicle security alarm is recorded [On]. This mode is able
to confirm and erase the record of vehicle security alarm. The trigger data can be
erased by touching [CLEAR].
CLEAR
Monitor Item [Unit]
Description
IGN ON SW [On/Off]
Indicates condition of ignition switch ON position.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
Test Item
Description
RETAINED PWR
This test is able to check retained power operation [Off/On].
Support Item
Setting
Description
RETAINED PWR SET
MODE3
2 min
Sets the retained accessory power operating time.
MODE2
OFF
MODE1*
45 sec
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
INFOID:0000000006161336
DATA MONITOR
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000006161338
SELF DIAGNOSTIC RESULT
NOTE:
Before performing Self Diagnostic Result, be sure to register the ID, or else the actual malfunction may be dif-
ferent from that displayed on CONSULT-III.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item [Unit]
Description
OIL PRESS SW [On/Off]
Indicates condition of oil pressure switch signal received from IPDM E/R on CAN communica-
tion line.
Test Item
Description
OIL PRESSURE SW
This test is able to check the oil pressure gauge operation [Off/On].
Monitor Item
Condition
Specification
VEHICLE SPEED
Drive vehicle
Vehicle speed (km/h or mph)
AIR PRESS FL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool is trans-
mitting activation signals.
Tire pressure (kPa, kg/cm
2
or psi).
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
ID REGST FL1
Ignition switch ON.
Registration ID: Green.
No registration: Red.
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
Ignition switch ON.
Low tire pressure warning lamp on: ON.
Low tire pressure warning lamp off: OFF.
BUZZER
Ignition switch ON.
Buzzer in combination meter on: ON.
Buzzer in combination meter off: OFF.
Test Item
Description
WARNING LAMP
This test is able to check tire pressure warning lamp operation [Off/On].
ID REGIST WARNING
This test is able to check ID regist warning chime operation [Off/On].
FLAT TIRE WARNING
This test is able to check flat tire warning chime operation [Off/On].
HORN
This test is able to check horn operation [On].
FLASHER
This test is able to check turn signal lamp operation [Off/LH/RH].
BCS-26
< SYSTEM DESCRIPTION >
[BCM]
DIAGNOSIS SYSTEM (BCM)
PANIC ALARM
PANIC ALARM : CONSULT-III Function (BCM - PANIC ALARM)
INFOID:0000000006628783
ACTIVE TEST
Support Item
Description
ID REGIST
WT-6, "ID Registration Procedure"
ID READ
The registered ID number is displayed.
Test Item
Description
HEAD LAMP (HI)
This test is able to check head lamp HI operation [On].
PANIC ALARM
This test is able to check panic alarm operation [On].
BCS
U1000 CAN COMM CIRCUIT
BCS-27
< DTC/CIRCUIT DIAGNOSIS >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000006161340
CAN Communication Signal Chart. Refer to
LAN-51, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000006161341
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000006161342
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-39, "Intermittent Incident"
.
DTC
CONSULT-III display
description
DTC Detection Condition
Possible cause
U1000
CAN COMM CIRCUIT
When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more.
Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
• Transmission
• Receiving (ECM)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст