Nissan Titan A60. Manual — part 875
SRC-16
< SYSTEM DESCRIPTION >
ON BOARD DIAGNOSTIC (OBD) SYSTEM
HOW TO CHANGE SELF-DIAGNOSIS MODE
DIAGNOSTIC PROCEDURE 3
Final Check of SRS Using CONSULT-III—Diagnosis Mode
1. Connect CONSULT-III.
2. If no DTC is detected on SELF-DIAG [CURRENT], repair of SRS is completed. Go to step 3.
If any DTC is detected on SELF-DIAG [CURRENT], the malfunctioning part has not been repaired com-
pletely or another malfunctioning part is being detected. Perform DIAGNOSTIC PROCEDURE 2. Refer to
.
3. Touch ERASE.
NOTE:
Touch ERASE to clear the memory of the malfunction (SELF-DIAG [PAST]).
If the memory of the malfunction in SELF-DIAG [PAST] is not erased, the User mode shows the system
malfunction by the operation of the warning lamp even if the malfunction is repaired completely.
4. Touch BACK key of CONSULT-III. Touch SELF-DIAG [PAST].
5. Check that no malfunction is detected on SELF-DIAG [PAST].
6. Touch BACK key of CONSULT-III to return to User mode from Diagnosis mode.
7. Turn ignition switch OFF and then turn off and disconnect CONSULT-III.
8. Go to
DIAGNOSTIC PROCEDURE 4
Check SRS Repair History
1.
CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes
>> Self-diagnostic result SELF-DIAG [PAST] (previously stored in the memory) might not be erased
after repair. Perform DIAGNOSTIC PROCEDURE 3. Refer to
SRC-15, "Self-Diagnosis Function
.
No
>> Perform DIAGNOSTIC PROCEDURE 2. Refer to
.
SHIA0183E
B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
SRC-17
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
DTC/CIRCUIT DIAGNOSIS
B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
Description
INFOID:0000000006163143
DTC B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable.
The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag mod-
ule including the spiral cable.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000006163144
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
CONSULT-III name
DTC
DTC detecting condition
Repair order
DRIVER AIRBAG MODULE
[OPEN]
B1049
Driver air bag module circuit (DR1) is open
(including the spiral cable).
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the driver air bag module.
4.
Replace the spiral cable.
5.
Replace the air bag diagnosis sensor unit.
6.
Replace the related harness.
B1054
Driver air bag module circuit (DR2) is open
(including the spiral cable).
DRIVER AIRBAG MODULE
[VB-SHORT]
B1050
Driver air bag module circuit (DR1) is
shorted to a power supply circuit
(including the spiral cable).
B1055
Driver air bag module circuit (DR2) is
shorted to a power supply circuit
(including the spiral cable).
DRIVER AIRBAG MODULE
[GND-SHORT]
B1051
Driver air bag module circuit (DR1) is
shorted to ground
(including the spiral cable).
B1056
Driver air bag module circuit (DR2) is
shorted to ground
(including the spiral cable).
DRIVER AIRBAG MODULE
[SHORT]
B1052
Driver air bag module circuits (DR1) are
shorted to each other
(including the spiral cable).
B1057
Driver air bag module circuits (DR2) are
shorted to each other
(including the spiral cable).
WHIA0260E
SRC-18
< DTC/CIRCUIT DIAGNOSIS >
B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES
>> Refer to
SRC-18, "Diagnosis Procedure (Component Diagnosis)"
.
NO
>> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5.
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6.
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component Diagnosis)
INFOID:0000000006163145
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
SRC-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
DRIVER AIR BAG MODULE
Replace the driver air bag module. Refer to
SR-4, "Removal and Installation"
.
>> GO TO 4
4.
SPIRAL CABLE
Replace the spiral cable. Refer to
SR-6, "Removal and Installation"
.
>> GO TO 5
5.
AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 6
6.
RELATED HARNESS
Replace the related harness.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст