Nissan Titan A60. Manual — part 185
BRC-118
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Removal and Installation
INFOID:0000000006165970
REMOVAL
1. Remove spiral cable. Refer to
SR-6, "Removal and Installation"
.
2. Remove the screws and remove the steering angle sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation of spiral cable, adjust steering angle sensor. Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
G SENSOR
BRC-119
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
G SENSOR
Removal and Installation
INFOID:0000000006165971
REMOVAL
1. If equipped, remove center console. Refer to
2. If equipped, remove the front center seat. Refer to
"Removal and Installation For Front Seat"
.
3. Remove yaw rate/side/decel G sensor nuts.
CAUTION:
• Do not use power tools to remove the yaw rate/side/decel
G sensor.
• Do not drop or strike the yaw rate/side/decel G sensor.
4. Disconnect harness connector and remove the yaw rate/side/
decel G sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not drop or strike the yaw rate/side/decel G sensor.
• After installation, calibrate the yaw rate/side/decel G sensor. Refer to
.
AWFIA0316ZZ
BRM-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
BRM
A
B
BRM
N
O
P
CONTENTS
BODY REPAIR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
FEATURES OF NEW MODEL . . . . . ..
BODY EXTERIOR PAINT COLOR . . . . . .
Body Exterior Paint Color . . . . . . . . . . ..
HANDLING PRECAUTIONS . . . . . . . ...
Handling Precaution for Plastics . . . . . . . ...
UNIT REMOVAL AND INSTALLATION . ...
BODY COMPONENT PARTS . . . . . . . .
Body Component Parts . . . . . . . . . . .....
CORROSION PROTECTION . . . . . . .
Body Sealing . . . . . . . . . . . . . . ...
Corrosion Protection . . . . . . . . . . . .
BODY CONSTRUCTION . . . . . . . . ..
Body Construction . . . . . . . . . . . . ...
Body Mounting, King Cab . . . . . . . . . .
Body Mounting, Crew Cab . . . . . . . . . ...
Rear Body . . . . . . . . . . . . . . . .
Foam Repair . . . . . . . . . . . . . . .
BODY ALIGNMENT . . . . . . . . . . ..
Body Alignment . . . . . . . . . . . . . ...
REPAIRING HIGH STRENGTH STEEL . . ...
Precaution in Repairing High Strength Steel . . ...
REPLACEMENT OPERATIONS . . . . . ...
BRM-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006158461
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст