Nissan Titan A60. Manual — part 480
ENGINE UNIT
EM-105
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• When the bearing cap is removed after being tightened to the
specified torque with main bearings installed, the tip end of the
bearing must protrude. Refer to
EM-89, "Disassembly and Assem-
• If standard is not met, replace main bearings.
CRUSH HEIGHT OF CONNECTING ROD BEARING
• When connecting rod bearing cap is removed after being tightened
to the specified torque with the connecting rod bearings installed,
the tip end of the bearing must protrude. Refer to
for tightening procedure.
• If standard is not met, replace connecting rod bearings.
MAIN BEARING CAP BOLT DIAMETER
• Check for bolts (M9 and M12) installed from lower side using the
following procedure.
NOTE:
• Side bolt (M10) is outside the target.
• Figure shows M12 bolt.
• Measure bolt diameter
″d1″ from tip of the bolt to dimension "a".
• Measure bolt diameter
″d2″ from the dimension between tip of the
bolt and dimension
″b″ as base station to dimension ″c″.
NOTE:
If a narrower part in the threads is determined by visual check,
measure
″d2″ at that point.
• Calculate the difference between
″d1″ and ″d2″.
M9 bolt
M12 bolt
• Replace applicable bolts if outside the limit.
CONNECTING ROD BOLT DIAMETER
• Measure diameter
″d″ at position shown.
Standard
: There must be crush height
SEM502G
Standard
: There must be crush height.
PBIC1646E
KBIA2497E
Dimension “a”
: 9 mm (0.35 in)
Dimension “b”
: 15 mm (0.59 in)
Dimension “c”
: 20 mm (0.79 in)
Limit
: 0.10 mm (0.0039 in)
Dimension “a”
: 12 mm (0.47 in)
Dimension “b”
: 55 mm (2.17 in)
Dimension “c”
: 20 mm (0.79 in)
Limit
: 0.15 mm (0.0059 in)
EM-106
< UNIT DISASSEMBLY AND ASSEMBLY >
ENGINE UNIT
• When “d” is out of specifications (when it becomes thinner),
replace bolt with a new one.
Limit
: 7.75 mm (0.3051 in) or less.
SBIA0286E
HOW TO SELECT PISTON AND BEARING
EM-107
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
HOW TO SELECT PISTON AND BEARING
How to Select Piston and Bearing
INFOID:0000000006179421
DESCRIPTION
*For the service parts, the grade for fitting cannot be selected between a piston pin and a connecting rod.
(Only 0 grade is available.) The information at the shipment from the plant is described as a reference.
• The identification grade stamped on each part is the grade for the dimension measured in new condition.
This grade cannot apply to reused parts.
• For reused or repaired parts, measure the dimension accurately. Determine the grade by comparing the
measurement with the values of each selection table.
• For details of the measurement method of each part, the reuse standards, and the selection method of the
selective fitting parts, follow the applicable procedure.
HOW TO SELECT PISTON
Piston Selective Fitting When New Cylinder Block is Used:
• Check the cylinder bore grade on the bottom face of the cylinder
block, and select the piston of the same grade.
Connecting points
Connecting parts
Selection items
Selection methods
Between cylinder block to
crankshaft
Main bearing
Main bearing grade (bearing
thickness)
Determined by match of cylin-
der block bearing housing
grade (Housing inside diame-
ter) and crankshaft journal
grade (journal outside diameter)
Between crankshaft to connect-
ing rod
Connecting rod bearing
Connecting rod bearing grade
(bearing thickness)
Connecting rod bearing grade =
crankshaft pin grade (pin diam-
eter). No grade exists for inside
diameter of connecting rod
large end.
Between cylinder block to pis-
ton
Piston and piston pin assembly.
The piston is available together
with piston pin as an assembly.
Piston grade (piston diameter)
Piston grade = cylinder bore
grade (diameter of bore)
*Between piston to connecting
rod
—
—
—
KBIA2495E
KBIA2496E
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >
HOW TO SELECT PISTON AND BEARING
When Cylinder Block is Reused
1. Measure cylinder block bore diameter.
2. Determine the bore grade by comparing the measurement with the values under the “Cylinder bore diam-
eter” of the piston selection table.
Piston Selection Table
Unit: mm (in)
NOTE:
• The piston is available together with piston pin as an assembly.
• The piston pin (piston pin bore) grade is provided only for the parts installed at the plant. For service parts,
no grades can be selected (only 0 grade is available).
HOW TO SELECT CONNECTING ROD BEARING
When New Connecting Rod and Crankshaft are Used
1. Apply the big end inside diameter grade stamped on the con-
necting rod side face to the row in the “Connecting Rod Bearing
Selection Table”.
2. Apply the pin diameter grade stamped on the crankshaft front
side to the column in the “Connecting Rod Bearing Selection
Table”.
3. Read the symbol at the cross point of the selected row and col-
umn in the “Connecting Rod Bearing Selection Table".
4. Apply the symbol obtained to the "Connecting Rod Bearing
Grade Table" to select.
When Crankshaft and Connecting Rod are Reused
1. Measure dimensions of the big end inside diameter of the connecting rod and diameter of the crankshaft
pin individually.
2. Apply the measured dimension to the “Connecting Rod Bearing Selection Table”.
3. The following steps are the same as in “When New Connecting Rod and Crankshaft are Used”.
Grade number (Mark)
1
2
3
Cylinder bore diameter
98.000-98.010 (3.8583-3.8587)
98.010-98.020 (3.8587-3.8590)
98.020-98.030 (3.8590-3.8594)
Piston diameter
97.980-97.990 (3.8575-3.8579)
97.990-98.000 (3.8579-3.8583)
98.000-98.010 (3.8583-3.8587)
KBIA2536E
PBIC0110E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст