Nissan Titan A60. Manual — part 293
TRANSFER ASSEMBLY
DLN-111
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Check the bearing for damage and rough rotation. If necessary,
replace it with a new one.
ASSEMBLY
1. Install the breather tube.
CAUTION:
Install breather tube in the direction shown.
2. Install the baffle plate to the front case. Tighten the bolt to the
specified torque. Refer to
DLN-103, "Disassembly and Assem-
CAUTION:
Install baffle plate by pushing it in the direction shown
while tightening the bolt.
3. Install the input bearing to the front case using Tool.
4. Install the new snap ring to the front case.
CAUTION:
Do not reuse snap ring.
MTF0041D
PDIA0107E
SDIA2479E
Tool number
: ST30720000 (J-25405)
PDIA0108E
PDIA0103E
DLN-112
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
5. Install the internal gear with the groove facing up into the front
case.
6. Install the new snap ring to the front case.
CAUTION:
Do not reuse snap ring.
7. Install the planetary carrier assembly and sun gear assembly to
the front case using Tool.
8. Install the new snap ring to the sun gear.
CAUTION:
• Do not reuse snap ring.
• Do not damage sun gear.
9. Set the L-H sleeve together with the L-H shift fork assembly onto
the planetary carrier assembly.
PDIA0102E
PDIA0101E
Tool number
: KV38100200 ( — )
SDIA2791E
PDIA0099E
SDIA2438E
TRANSFER ASSEMBLY
DLN-113
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
10. Install the control shift rod assembly to the front case.
CAUTION:
Set pin of L-H shift fork assembly into the groove of drum
cam.
11. Turn the control shift rod assembly fully counterclockwise.
12. Install the L-H shift rod assembly through the L-H shift fork
assembly opening to the front case.
CAUTION:
Set pin of L-H shift rod assembly into the groove of drum
cam.
13. Install the mainshaft to the sun gear assembly.
14. Install the drive chain to the front drive shaft and sprocket.
CAUTION:
Install with the Identification mark of drive chain on the side
of the rear bearing of front drive shaft.
15. Install the drive chain together with the front drive shaft and
sprocket to the front case.
16. Install the 2-4 sleeve and 2-4 shift fork assembly to the main-
shaft.
CAUTION:
• Install with proper orientation of 2-4 sleeve.
• Install 2-4 shift fork with engaging the grooves of 2-4 shift
fork in the retaining pin of 2-4 shift bracket.
WDIA0215E
WDIA0216E
PDIA0110E
SDIA2464E
SDIA2467E
DLN-114
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
17. Install the new snap ring to the L-H shift rod assembly using suit-
able tool.
CAUTION:
Do not reuse snap ring.
18. Install the clutch gear to the mainshaft.
19. Install the new snap ring to the mainshaft using suitable tool.
CAUTION:
Do not reuse snap ring.
20. Install the oil pump assembly to the mainshaft.
21. Install the new snap ring to the mainshaft using suitable tool.
CAUTION:
Do not reuse snap ring.
22. Install the retainer to the mainshaft.
CAUTION:
Set the projection of oil pump assembly to the identification
hole, and then align locating hole of retainer to the L-H shift
rod assembly.
23. Install the mainshaft rear bearing to the mainshaft using Tool.
CAUTION:
Do not push too hard in order to avoid snap rings becoming
dislodged from mainshaft.
SDIA2463E
SDIA2462E
SDIA2461E
SDIA2468E
Tool number
: KV32102700 ( — )
SDIA2469E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст