Nissan Titan A60. Manual — part 332
REAR FINAL DRIVE
DLN-267
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: M226 (ELD) ]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Remove sensor connector bolts and disconnect differential lock
solenoid connector.
4. For proper reinstallation, paint matching mark on one side of
side bearing cap.
CAUTION:
• Side bearing caps are line-board for initial assembly. The
matching marks are used to reinstall them in their original
positions.
• For matching mark, use paint. Do not damage side bear-
ing cap.
5. Remove adjuster lock plates.
6. Remove side bearing caps.
7. Loosen side bearing adjusters using Tool.
8. Remove differential lock position switch.
9. Remove differential lock position switch bracket.
SDIA2585E
SDIA2583E
PDIA0331E
Tool number
: — (C - 4164)
PDIA0337E
DLN-268
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: M226 (ELD) ]
REAR FINAL DRIVE
10. Remove the differential case assembly. Label side bearing outer
races to keep them together with inner races. Do not mix them
up.
Drive Pinion Assembly
1. Put matching marks on the companion flange at location (A) and
drive pinion using paint as shown.
CAUTION:
Use paint to make the matching marks. Do not damage the
companion flange or drive pinion.
2. Remove drive pinion lock nut and washer using suitable tool.
3. Remove companion flange using a suitable tool.
4. Remove oil seal/dust shield and discard.
SDIA2588E
PDIA0675E
PDIA0314E
PDIA0315E
REAR FINAL DRIVE
DLN-269
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: M226 (ELD) ]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5. Remove front oil seal using Tool.
CAUTION:
Do not damage gear carrier.
6. Remove drive pinion front bearing thrust washer.
7. Remove drive pinion assembly (with rear inner bearing race and
collapsible spacer) out of gear carrier.
CAUTION:
Do not drop drive pinion assembly.
8. Remove collapsible spacer from drive pinion assembly and discard collapsible spacer.
CAUTION:
Do not reuse the collapsible spacer.
INSPECTION AFTER DISASSEMBLY
Clean the disassembled parts. Then inspect the parts for wear or damage. If wear or damage are found, follow
the measures below.
Drive Pinion and Drive Gear
• If the gear teeth do not mesh or line-up correctly, replace with new rear final drive assembly. Refer to
263, "Disassembly and Assembly"
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new rear final
drive assembly. Refer to
DLN-263, "Disassembly and Assembly"
.
Bearings
• If bearings are chipped (by friction), pitted, worn, rusted, scratched mark, or unusual noise from the bearing,
replace with new rear final drive assembly. Refer to
DLN-263, "Disassembly and Assembly"
Differential Case Assembly
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new rear final
drive assembly. Refer to
DLN-263, "Disassembly and Assembly"
.
• If the movement is not smooth when pushing cam ring of differential case assembly by hand. Replace with
new rear final drive assembly. Refer to
DLN-263, "Disassembly and Assembly"
Differential Lock Solenoid
• If the operating part of differential lock solenoid is not smooth, perform component inspection. Refer to
216, "CONSULT-III Function (DIFF LOCK)"
Companion Flange
• If any chips [about 0.1mm (0.004 in)] or other damage on the companion flange surface which contacts the
front oil seal lips are found, replace with new one. Refer to
DLN-263, "Disassembly and Assembly"
ASSEMBLY
Drive Pinion Assembly
1. Install drive pinion front bearing thrust washer.
Tool number
: ST33290001 (J-34286)
SDIA2586E
PDIA0316E
DLN-270
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: M226 (ELD) ]
REAR FINAL DRIVE
2. Apply multi-purpose grease to new front oil seal lip. Install new
front oil seal into gear carrier using Tool.
CAUTION:
• Do not reuse front oil seal.
• Do not incline the new front oil seal when installing.
• Apply multi-purpose grease to the lips of the new front oil
seal.
3. Install new collapsible spacer on drive pinion assembly. And
then install drive pinion assembly into gear carrier.
CAUTION:
• Do not reuse collapsible spacer.
• Do not damage front oil seal.
4. Install a new oil seal/dust shield.
5. Install the companion flange onto the drive pinion while aligning
the matching marks. Then tap the companion flange using suit-
able tool.
CAUTION:
Do not damage companion flange or front oil seal.
Tool number
: ST15310000 ( — )
PDIA0326E
SDIA2595E
PDIA0328E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст