Nissan Titan A60. Manual — part 303
REAR PROPELLER SHAFT
DLN-151
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2WD Models (long wheel base)
4WD Models (long wheel base)
AWDIA0787GB
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Center support bearing
7.
Center support bearing bracket
8.
Slip yoke
9.
Flange yoke
: Front
AWDIA0788GB
DLN-152
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
REAR PROPELLER SHAFT
REMOVAL
1. Move the A/T select lever to the N position and release the parking brake.
2. Put matching marks on the rear propeller shaft flange yoke and
the companion flange of the rear final drive as shown.
CAUTION:
For matching marks, use paint. Never damage the rear pro-
peller shaft flange yoke or the companion flange.
3. Remove the center support bearing bracket nuts, and remove
the propeller shaft from the rear final drive.
INSPECTION AFTER REMOVAL
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts.
• Check the propeller shaft tube for bend and damage. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Center support bearing
7.
Center support bearing bracket
8.
Slip yoke
9.
Flange yoke
: Front
WDIA0065E
WDIA0066E
PDIA0420E
Journal axial play : 0.02 mm (0.0008 in) or less
LDIA0117E
REAR PROPELLER SHAFT
DLN-153
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-148, "NVH Troubleshooting Chart"
.
• If propeller shaft assembly of final drive assembly has been
replaced, connect them as follows:
- Face companion flange mark (A) of the final drive (1) upward. With
the mark (A) faced upward, couple the propeller shaft and the final
drive so that the matching mark (B) of the propeller shaft (2) can be
positioned as close as possible with the matching mark (C) of the
final drive companion flange.
- Tighten propeller shaft and final drive bolts and nuts of the to spec-
DLN-150, "Removal and Installation"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
PDIA0892J
DLN-154
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1410]
REAR PROPELLER SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
REAR PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000006179535
DISASSEMBLY
Journal
1. Remove the propeller shaft assembly from the vehicle. Refer to
DLN-150, "Removal and Installation"
2. Put matching marks on the rear propeller shaft tube and flange
yoke as shown.
CAUTION:
For matching marks use paint. Never damage the rear pro-
peller shaft or flange yoke.
3. Remove the snap rings.
4. Push out and remove the journal bearing by lightly tapping the
yoke with a hammer, taking care not to damage the journal or
yoke hole.
5. Remove the bearing at the opposite side of above operation.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
SPD128
APD011
SPD732
SPD131
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст