Nissan Pathfinder (2008 year). Manual — part 462
ILLUMINATION
INL-47
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ALLIA0444GB
INL-48
< COMPONENT DIAGNOSIS >
ILLUMINATION
ALLIA0445GB
ILLUMINATION
INL-49
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ALLIA0446GB
INL-50
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Description
INFOID:0000000001712591
REFERENCE VALUES FOR BCM
For BCM reference values, refer to
TERMINAL LAYOUT FOR BCM
For the terminal layout for the BCM, refer to
.
PHYSICAL VALUES FOR BCM
For physical values for the BCM, refer to
.
WIRING DIAGRAM - BCM
For the BCM wiring diagram, refer to
.
DTC INSPECTION PRIORITY CHART - BCM
For the BCM DTC inspection priority chart, refer to
BCS-50, "DTC Inspection Priority Chart"
DTC INDEX - BCM
For the BCM DTC index, refer to
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-51
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000001712592
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
All of the following lamps do not turn ON
• Front room/map lamp assembly
• Personal lamp 2nd row (with rear map lamps)
• Room lamp 2nd row (without rear map lamps)
• Cargo room lamp
• Vanity mirror lamps (if equipped)
• Ignition keyhole illumination
• Harness between BCM and each
interior room lamp
• Harness between BCM and each
door switch
• BCM
Battery saver output/power supply
circuit
Refer to
.
Some or all of the following interior room lamps
do not turn ON/OFF
• Front room/map lamp assembly
• Personal lamp 2nd row (with rear map lamps)
• Room lamp 2nd row (without rear map lamps)
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp control circuit
Refer to
.
Cargo lamp does not turn ON/OFF
• Harness between BCM and cargo
lamp
• BCM
Cargo lamp circuit
Refer to
.
Ignition keyhole illumination does not turn ON/
OFF
• Harness between BCM and cargo
lamp
• BCM
Ignition keyhole illumination circuit
Refer to
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
Interior room lamp battery saver does not acti-
vate.
—
Check the interior room lamp battery
saver setting.
Refer to
INL-52
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER"
INFOID:0000000001702208
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
General precautions for service operations
INFOID:0000000001702209
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
• When removing parts with a screw driver or other tool, protect parts by wrapping them with vinyl or tape.
• Keep removed parts protected with cloth.
• If an non-reuseable part is removed, replace it with a new one.
• After re-assembly has been completed, make sure each part functions correctly.
• Never work with wet hands.
• Turn the lighting switch OFF before disconnecting and connecting the connector.
• Do not use organic solvent (paint thinner or gasoline) to clean lamps or remove sealant residue.
INTERIOR ROOM LAMP
INL-53
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ON-VEHICLE REPAIR
INTERIOR ROOM LAMP
Removal and Installation
INFOID:0000000001697740
MAP LAMP
Removal
The map lamp is replaced as part of the overhead console assembly.
Refer to
INT-16, "Removal and Installation"
.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1.
Disconnect the negative battery terminal.
2.
Using a suitable tool (A), remove map lamp lens (1).
⇐
: Vehicle front
CAUTION:
Wrap a cloth around tool to protect the housing and lens.
3.
Release one side of the bulb (2) from the tab, then pull straight
downward to remove.
VANITY MIRROR LAMP
Removal
ALLIA0581ZZ
Map lamp bulb
: 12V - 8W
ALLIA0582ZZ
INL-54
< ON-VEHICLE REPAIR >
INTERIOR ROOM LAMP
The vanity mirror lamp is replaced as part of the sunvisor assembly.
Refer to
INT-16, "Removal and Installation"
.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
The vanity mirror lamp bulb is replaced as part of the sunvisor assembly. Refer to
GLOVE BOX LAMP
Removal
1.
Remove lower instrument panel RH and glove box. Refer to
IP-10, "Removal and Installation"
2.
Rotate glove box lamp socket (3) with bulb (1) counterclockwise,
then pull away from lamp shield (2) on steering member to
remove.
⇐
: Vehicle front
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1.
Disconnect the negative battery terminal.
2.
Remove glove box lamp.
3.
Pull bulb (2) straight out from glove box lamp socket (1) to
remove.
PERSONAL LAMP
Removal
1.
Disconnect the negative battery terminal.
ALLIA0583ZZ
ALLIA0587ZZ
Glove box lamp bulb
: 12V - 3.4W
ALLIA0321ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст