Nissan Pathfinder (2008 year). Manual — part 233
DLN-448
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
7.
Place a suitable jack under the rear final drive assembly.
CAUTION:
Do not place the jack on the carrier cover.
8.
Remove the nuts and bolts and remove the rear final drive
assembly.
CAUTION:
Secure rear final drive assembly to the jack while removing
it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing the breather hose make sure the painted marking on the metal end of breather hose
is to the front of the vehicle and there are no pinched or restricted areas on the breather hose
caused by folding or bending when installing it.
• When installing the breather hose insert the plastic end of the breather hose into the hole in the sus-
pension member.
REAR FINAL DRIVE BREATHER
WDIA0117E
LDIA0166E
1.
Breather hose
2.
Plastic connector
3.
Rear final drive assembly
4.
Metal connector
5.
Paint mark
REAR FINAL DRIVE
DLN-449
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Fill the rear final drive assembly with differential gear oil after installation. Refer to
DLN-450
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
DISASSEMBLY AND ASSEMBLY
REAR FINAL DRIVE
Disassembly and Assembly
INFOID:0000000001316530
COMPONENTS
WDIA0191E
REAR FINAL DRIVE
DLN-451
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ASSEMBLY INSPECTION AND ADJUSTMENT
• Drain the differential gear oil before inspection and adjustment. Refer to
.
• Remove and install the carrier cover as necessary for inspection and adjustment. Refer to
.
Total Preload Torque
1.
Remove the side flanges if necessary. Refer to
DLN-444, "Removal and Installation"
.
CAUTION:
The side flanges shaft must removed in order to measure total preload torque.
2.
Rotate the drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction.
3.
Rotate the drive pinion at least 20 times to check for smooth operation of the bearings.
4.
Measure the total preload torque using Tool.
NOTE:
Total preload torque = Drive pinion bearing preload torque +
Side bearing preload torque
• If the measured value is out of the specification, check and adjust each part. Adjust the drive pinion
bearing preload torque first, then adjust the side bearing preload torque.
CAUTION:
Select a side bearing adjusting washer for right and left individually.
Drive Gear Runout
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Drive pinion front bearing
5.
Collapsible spacer
6.
Drive pinion rear bearing
7.
Drive pinion height adjusting
washer
8.
Drive pinion
9.
Gear carrier
10. Drive gear
11.
Pinion mate shaft
12. Lock pin
13. Pinion mate gear
14. Pinion mate thrust washer
15. Side gear
16. Side gear thrust washer
17. Differential case
18. Side bearing
19. Side bearing adjusting washer
20. Bearing cap
21. Carrier cover
22. Filler plug
23. Drain plug
24. Side oil seal
Tool number
: ST3127S000 (J-25765-A)
Total preload torque:
2.05 - 4.11 N·m (0.21 - 0.42 kg-m, 19 - 36 in-lb)
SPD884
If the total preload torque is greater than specification
On drive pinion bearings:
Replace the collapsible spacer.
On side bearings:
Use thinner side bearing adjusting washers by the same
amount on each side. Refer to
DLN-466, "Inspection and Adjust-
If the total preload torque is less than specification
On drive pinion bearings:
Tighten the drive pinion lock nut.
On side bearings:
Use thicker side bearing adjusting washers by the same
amount on each side. Refer to
DLN-452
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
1.
Fit a dial indicator to the drive gear back face.
2.
Rotate the drive gear to measure runout.
• If the runout is outside of the limit, check the condition of the drive
gear assembly. Foreign material may be caught between the drive
gear and differential case, or the differential case or drive gear may
be deformed.
CAUTION:
Replace drive gear and drive pinion as a set.
Tooth Contact
1.
Apply red lead to the drive gear.
NOTE:
Apply red lead to both faces of three to four gears, at four loca-
tions evenly spaced on the drive gear.
2.
Rotate the drive gear back and forth several times. Then check
for correct drive pinion to drive gear tooth contact as shown.
CAUTION:
Check tooth contact on drive side and reverse side.
3.
If the tooth contact is improperly adjusted, follow the procedure
below to adjust the pinion height (dimension X).
Runout limit
: 0.05 mm (0.0020 in) or less
SPD886
SPD357
SDIA0570E
SDIA0517E
REAR FINAL DRIVE
DLN-453
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• If the tooth contact is near the face (face contact), or near the heel
(heel contact), use a thicker drive pinion height adjusting washers
to move the drive pinion closer to the drive gear.
Refer to
DLN-466, "Inspection and Adjustment"
• If the tooth contact is near the flank (flank contact), or near the toe
(toe contact), use a thinner drive pinion height adjusting washers to
move the drive pinion farther from the drive gear.
Refer to
DLN-466, "Inspection and Adjustment"
Backlash
1.
Fit a dial indicator to the drive gear face to measure the back-
lash.
• If the backlash is outside of the specification, change the thickness
of the side bearing adjusting washers.
CAUTION:
Do not change the total thickness of side bearing adjusting washers as it will change the side bearing
preload torque.
Companion Flange Runout
PDIA0440E
PDIA0441E
Backlash
: 0.13 - 0.18 mm (0.0051 - 0.0070 in)
If the backlash is greater than specification:
Make side bearing adjusting washer thicker on drive
gear back side, and side bearing adjusting washer
thinner on drive gear tooth side by the same amount.
Refer to
DLN-466, "Inspection and Adjustment"
.
If the backlash is less than specification:
Make side bearing adjusting washer thinner on drive
gear back side, and side bearing adjusting washer
thicker on drive gear tooth side by the same amount.
Refer to
DLN-466, "Inspection and Adjustment"
.
SPD513
DLN-454
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
1.
Rotate companion flange and check for runout on the outer face
of the companion flange using suitable tool.
2.
If the runout is outside of the runout limit, follow the procedure
below to adjust.
a.
Rotate the companion flange on the drive pinion by 90
°
, 180
°
and 270
°
while checking for the position where the runout is
minimum.
b.
If the runout is still outside of the runout limit after the companion
flange has been rotated on the drive pinion, possible cause
could be an assembly malfunction of drive pinion and drive pinion bearing or a malfunctioning drive pinion
bearing.
c.
If the runout is still outside of the runout limit after repair of the assembly of drive pinion and drive pinion
bearing or drive pinion bearing, replace the companion flange.
DISASSEMBLY
Side Flange
1.
Drain the differential gear oil if necessary.
2.
Remove the side flange using Tools.
3.
Remove the side oil seal using suitable tool.
CAUTION:
Do not to damage gear carrier.
Differential Assembly
1.
Remove the side flanges. Refer to
DLN-444, "Removal and Installation"
.
2.
Remove the carrier cover bolts.
3.
Remove the carrier cover bolts and separate the carrier cover
from the gear carrier using Tool.
CAUTION:
• Do not damage the mating surface.
• Do not insert flat-bladed screwdriver, this will damage the
mating surface.
4.
Mount the carrier on the Tool using two 45 mm (1.77 in) spacers.
Runout limit
: 0.08 mm (0.0031 in) or less
WDIA0231E
Tool numbers
A: KV40104100 (
—
)
B: ST36230000 (J-25840-A)
Tool number
: KV10111100 (J-37228)
WDIA0123E
Tool number
: KV38100800 (J-25604-01)
SPD888
REAR FINAL DRIVE
DLN-455
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5.
For proper reinstallation, paint matching marks on one side of
the side bearing cap and gear carrier.
CAUTION:
• For matching marks, use paint. Do not damage side bear-
ing cap or gear carrier.
• Side bearing caps are line-board during manufacture. The
matching marks are used to reinstall them in their original
positions.
6.
Remove the side bearing caps.
7.
Lift the differential case assembly out using Tool.
CAUTION:
• Keep side bearing outer races together with inner race.
Do not mix them up.
• Keep side bearing adjusting washers together with side
bearings.
SDIA1795E
S-PD343
Tool number
: HT72400000 (
—
)
S-PD344
SPD919
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст