Nissan Pathfinder (2008 year). Manual — part 9
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-59
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
YES
>> GO TO 5
NO
>> Replace automatic drive positioner control unit.
5.
CHECK MIRROR SWITCH
Check mirror switch.
Refer to
ADP-59, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-51, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch.
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-51, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit.
NO
>> Repair or replace the malfunctioning parts.
MIRROR SWITCH : Component Inspection
INFOID:0000000001711044
1.
CHECK MIRROR SWITCH
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch.
Terminal
Mirror switch condition
Continuity
Door mirror remote
control switch
4
13
RIGHT
Yes
Other than above
No
5
LEFT
Yes
Other than above
No
6
UP
Yes
Other than above
No
14
DOWN
Yes
Other than above
No
LIIA2053E
ADP-60
< COMPONENT DIAGNOSIS >
POWER SEAT SWITCH GROUND CIRCUIT
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000001711045
1.
CHECK POWER SEAT SWITCH LH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch LH.
3.
Check continuity between power seat switch LH connector and
ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
NO
>> Repair or replace harness.
Power seat switch LH
connector
Terminal
Ground
Continuity
B208
32
Yes
LIIA1133E
DETENTION SWITCH
ADP-61
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DETENTION SWITCH
Description
INFOID:0000000001711046
Park position switch is installed on A/T device. It is turned OFF when the A/T selector lever is in P position.
The driver seat control unit judges that the A/T selector lever is in P position if continuity does not exist in this
circuit.
Component Function Check
INFOID:0000000001711047
1.
CHECK FUNCTION
1.
Select “DETENT SW” signal in “Data monitor” mode with CONSULT-III.
2.
Check park position switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000001711048
1.
CHECK DTC WITH “BCM”
Check “Self Diagnostic Result” for BCM with CONSULT-lll.
Is any other DTC detected?
YES
>> Check the DTC.
NO
>> GO TO 2
2.
CHECK PARK POSITION SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Mechanical key must be removed from the key switch.
3.
Check voltage between driver seat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 3
3.
CHECK PARK POSITION SWITCH CIRCUIT
Monitor item
Condition
Status
DETENT SW
A/T selector lever
P position
OFF
Other than
above
ON
Driver seat
control unit
connector
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(-)
B202
21
Ground
A/T selec-
tor lever
P position
Battery volt-
age
Other than
above
0V
LIIA2238E
ADP-62
< COMPONENT DIAGNOSIS >
DETENTION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and A/T device.
3.
Check continuity between driver seat control unit harness con-
nector and A/T device harness connector.
4.
Check continuity between A/T device harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-51, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit.
NO
>> Repair or replace the malfunctioning part.
Driver seat control unit
A/T device
Continuity
Connector
Terminal
Connector
Terminal
B202
21
M156
4
Yes
A/T device
—
Continuity
Connector
Terminal
Mi56
4
Ground
No
LIIA1774E
FRONT DOOR SWITCH (DRIVER SIDE)
ADP-63
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FRONT DOOR SWITCH (DRIVER SIDE)
Description
INFOID:0000000001711049
Detects front door LH open/close condition.
Component Function Check
INFOID:0000000001711050
1.
CHECK FUNCTION
1.
Select “DOOR SW-DR” in “Data monitor” mode with CONSULT-III.
2.
Check the front door switch LH signal under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000001711051
1.
CHECK FRONT DOOR SWITCH LH CIRCUIT
1.
Disconnect BCM.
2.
Check continuity between BCM connector and front door switch
LH connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace harness.
2.
CHECK FRONT DOOR SWITCH LH
ADP-63, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace front door switch LH.
3.
CHECK INTERMITTENT INCIDENT
GI-51, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-54, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000001711052
1.
CHECK FRONT DOOR SWITCH LH
Monitor item
Condition
Status
DOOR SW-DR
Front door switch LH
Open
ON
Close
OFF
BCM connector
Terminal
Front door switch
LH connector
Terminal
Continuity
M19
47
B8
2
Yes
BCM connector
Terminal
Ground
Continuity
M19
47
No
LIIA1027E
ADP-64
< COMPONENT DIAGNOSIS >
FRONT DOOR SWITCH (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front door switch LH.
3.
Check continuity between front door switch LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door switch LH.
Terminal
Condition
Continuity
Front door switch LH
2
Ground part of
door switch
Front door switch
LH
Pushed
No
Released
Yes
LIIA2377E
SLIDING SENSOR
ADP-65
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SLIDING SENSOR
Description
INFOID:0000000001711053
• The sliding sensor is installed to the seat slide cushion frame.
• The pulse signal is input to the driver seat control unit when sliding is performed.
• The driver seat control unit counts the pulse and calculates the sliding amount of the seat.
Component Function Check
INFOID:0000000001711054
1.
CHECK FUNCTION
1.
Select “SLIDE PULSE” in “Data monitor” mode with CONSULT-III.
2.
Check sliding sensor signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000001711055
1.
CHECK SLIDING SENSOR SIGNAL
1.
Turn ignition switch ON.
2.
Read voltage signal between driver seat control unit harness
connector and ground with osiloscope.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 2
2.
CHECK SLIDING SENSOR CIRCUITS
Monitor item
Condition
Valve
SLIDE PULSE
Seat sliding
Operate (forward)
Change (increase)
Operate (backward)
Change (decrease)
Release
No change
Terminals
Condition
Voltage signal
(+)
(–)
Driver’s
seat
control
unit
Termi-
nal
B202
24
Ground
Seat
sliding
Operate
Other
than
above
0 or 5
PIIA4556E
PIIA3277E
ADP-66
< COMPONENT DIAGNOSIS >
SLIDING SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and sliding motor LH.
3.
Check continuity between driver seat control unit harness con-
nector and sliding motor LH harness connector.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK SEAT OPERATION
1.
Connect driver seat control unit and sliding motor LH.
2.
Check seat operation (except sliding operation) with memory function.
Is the inspection result normal?
YES
>> Replace sliding motor LH. (Built in seat slide cushion frame).
NO
>> Replace driver seat control unit.
4.
CHECK INTERMITTENT INCIDENT
GI-51, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit.
NO
>> Repair or replace the malfunctioning part.
Driver seat control
unit connector
Terminal
Sliding motor
LH connector
Terminal
Continuity
B202
16
B204
3
Yes
24
2
31
1
Driver seat control unit
connector
Terminal
Ground
Continuity
B202
16
No
24
31
LIIA0706E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст