Nissan Pathfinder (2008 year). Manual — part 116
BRC-234
< REMOVAL AND INSTALLATION >
[HDC/HSA/VDC/TCS/ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Removal and Installation
INFOID:0000000001297856
REMOVAL
1.
Disconnect the battery negative terminal.
2.
Drain the brake fluid. Refer to
.
3.
Disconnect the actuator harness from the ABS actuator and electric unit (control unit).
CAUTION:
• To remove the brake tubes, use a flare nut wrench to prevent the flare nuts and brake tubes from
being damaged.
• Be careful not to splash brake fluid on painted areas.
4.
Disconnect the brake tubes.
5.
Remove the three bolts and remove the ABS actuator and electric unit (control unit).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
To install, use a flare nut wrench (commercial service tool).
• Always tighten brake tubes to specification when installing. Refer to
.
• Never reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the air from the system. Refer to
.
NOTE:
LFIA0244E
1. To rear left disc brake
2. To rear right disc brake
3. To front left disc brake
4. To front right disc brake
5. From the master cylinder secondary
side
6. From the master cylinder primary
side
7. ABS actuator and electric unit
(control unit)
8. Harness connector
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
BRC-235
< REMOVAL AND INSTALLATION >
[HDC/HSA/VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
In the case that ABS actuator and electric unit (control unit) is replaced, make sure to adjust position of steer-
ing angle sensor. Refer to
BRC-131, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
BRC-236
< REMOVAL AND INSTALLATION >
[HDC/HSA/VDC/TCS/ABS]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Removal and Installation
INFOID:0000000001297857
REMOVAL
1.
Remove the spiral cable. Refer to
SR-6, "Removal and Installation"
2.
Remove the screws and remove the steering angle sensor.
CAUTION:
In the case that the ABS actuator and electronic unit (control unit) is replaced, make sure to adjust
position of steering angle sensor. Refer to
BRC-131, "ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Special Repair Requirement"
INSTALLATION
1.
Installation is in the reverse order of removal.
WHEEL SENSORS
BRC-237
< REMOVAL AND INSTALLATION >
[HDC/HSA/VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
WHEEL SENSORS
Removal and Installation
INFOID:0000000001297854
REMOVAL
1.
Remove wheel and tire using power tool.
2.
Remove wheel sensor mounting screw.
NOTE:
• When removing the front wheel sensor, first remove the disc rotor to gain access to the front wheel sen-
sor bolt. Refer to
BR-26, "Removal and Installation of Brake Caliper and Disc Rotor"
.
• When removing rear wheel sensor, first remove spare tire.
3.
Pull out the wheel sensor, being careful to turn it as little as possible.
CAUTION:
• Be careful not to damage sensor edge and sensor rotor teeth.
• Do not pull on the sensor harness.
4.
Disconnect wheel sensor harness electrical connector, then remove harness from mounts.
INSTALLATION
Installation is in the reverse order of removal. When installing wheel and tire, refer to
.
CAUTION:
• Inspect wheel sensor O-ring, replace sensor assembly if damaged.
• Clean wheel sensor hole and mounting surface with brake cleaner and a lint-free shop rag. Be care-
ful that dirt and debris do not enter the axle.
NOTE:
• Apply a coat of suitable grease to the wheel sensor O-ring and mounting hole.
• Tighten wheel sensor bolt to specification.
WFIA0333E
BRC-238
< REMOVAL AND INSTALLATION >
[HDC/HSA/VDC/TCS/ABS]
G SENSOR
G SENSOR
Removal and Installation
INFOID:0000000001297858
REMOVAL
1.
Remove center console. Refer to
2.
Remove yaw rate/side/decel G sensor nuts as shown.
• The location of the sensor is the same for all models.
CAUTION:
• Do not use power tools to remove or install yaw rate/side/
decel G sensor.
• Do not drop or strike the yaw rate/side/decel G sensor.
3.
Disconnect harness connector and remove the yaw rate/side/
decel G sensor.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After performing the above work, calibrate the decel G sensor. Refer to
BRC-132, "CALIBRATION OF DECEL
G SENSOR : Special Repair Requirement"
.
WFIA0230E
BRM-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
BRM
A
B
BRM
N
O
P
CONTENTS
BODY REPAIR
SERVICE INFORMATION . . . . . . .
BODY REPAIR . . . . . . . . . . . . .
Body Exterior Paint Color . . . . . . . . . . ..
Body Component Parts . . . . . . . . . . .....
Body Mounting . . . . . . . . . . . . . . ..
Corrosion Protection . . . . . . . . . . . .....
Body Sealing . . . . . . . . . . . . . . ...
Body Construction . . . . . . . . . . . . ...
Body Alignment . . . . . . . . . . . . . ...
Handling Precaution for Plastics . . . . . . . ..
Precaution in Repairing High Strength Steel . . ...
Foam Repair . . . . . . . . . . . . . . .
BRM-2
< SERVICE INFORMATION >
BODY REPAIR
SERVICE INFORMATION
BODY REPAIR
Body Exterior Paint Color
INFOID:0000000001697780
M: Metallic; S: 1-Coat Solid; 2S: 2-Coat Solid, 2P: 2-Coat Pearl; PM: Pearl + Metallic
LIIA1735E
Component
Color
code
A15
B25
BW9
C43
E50
Q50
K12
K27
KH3
QM1
De-
scrip-
tion
Red
Brawn
Silver-
ton
Blue
Majestic
Blue
Desert
Stone
Mocha
White
Frost
Silver
Lightning
Storm
Gray
Super
Black
Ava-
lanche
Paint
type
PM
PM
PM
M
M
P
M
M
2S
S
Clear
coat
t
t
t
t
t
t
t
t
t
t
1
Out-
side
mirror
Body
color
A15
B25
BW9
C43
E50
Q50
K12
K27
KH3
QM1
XE
Black
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
2
Side
Guard
Mold-
ing
Body
color
A15
B25
BW9
C43
E50
Q50
K12
K27
KH3
QM1
3
Bump
ers
Fas-
cias
Body
color
A15
B25
BW9
C43
E50
Q50
K12
K27
KH3
QM1
4
Out-
side
han-
dles
Body
color
A15
B25
BW9
C43
E50
Q50
K12
K27
KH3
QM1
5
Radia-
tor
grille
Cen-
ter
and
em-
blem
Chro-
mium
plate
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cen-
ter
Black
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
KH3
6
Li-
cense
Lamp
Finish-
er
Chro-
mium
plate
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
Cr2P
BODY REPAIR
BRM-3
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Body Component Parts
INFOID:0000000001697781
UNDERBODY COMPONENT PARTS
1.
Rear floor side RH
2.
Rear floor
3.
Storage bin
4.
Second seat mounting crossmember
LIIA1787E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст