Nissan Pathfinder (2008 year). Manual — part 355
EM-3
C
D
E
F
G
H
I
J
K
L
M
EM
A
N
O
P
CYLINDER HEAD . . . . . . . . . . .
Removal and Installation . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ..
Inspection After Disassembly . . . . . . . .
REMOVAL AND INSTALLATION . . . .
ENGINE ASSEMBLY . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
DISASSEMBLY AND ASSEMBLY . . .
ENGINE UNIT . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ...
Inspection After Disassembly . . . . . . . .
HOW TO SELECT PISTON AND BEARING ..
How to Select Piston and Bearing . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
EM-4
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001281958
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Drain Engine Coolant
INFOID:0000000001281959
Drain engine coolant when engine is cooled.
Precaution for Disconnecting Fuel Piping
INFOID:0000000001281960
• Before starting work, make sure no fire or spark producing items are in the work area.
• Release fuel pressure before disconnecting and disassembly.
• After disconnecting pipes, plug openings to stop fuel leakage.
Precaution for Removal and Disassembly
INFOID:0000000001281961
• When instructed to use special service tools, use the specified tools. Always be careful to work safely, avoid
forceful or uninstructed operations.
• Exercise maximum care to avoid damage to mating or sliding surfaces.
• Cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials.
• Mark and arrange disassembly parts in an organized way for easy troubleshooting and re-assembly.
• When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified. Power tools may be used
in the step.
Precaution for Inspection, Repair and Replacement
INFOID:0000000001281962
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Precaution for Assembly and Installation
INFOID:0000000001281963
• Use torque wrench to tighten bolts or nuts to specification.
• When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified,
do exactly as specified.
• Replace with new gasket, packing, oil seal or O-ring.
• Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for
any restriction and blockage.
• Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.
PRECAUTIONS
EM-5
< PRECAUTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Release air within route when refilling after draining engine coolant.
• Before starting engine, apply fuel pressure to fuel lines with turning ignition switch ON (with engine stopped).
Then make sure that there are no leaks at fuel line connections.
• After repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust gasses for leakage.
Parts Requiring Angle Tightening
INFOID:0000000001281964
• For the final tightening of the following engine parts use Tool:
- Cylinder head bolts
- Lower cylinder block bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (No angle wrench is required as bolt flange is provided with notches for angle tighten-
ing)
• Do not use a torque value for final tightening.
• The torque value for these parts are for a preliminary step.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Precaution for Liquid Gasket
INFOID:0000000001281965
REMOVAL OF LIQUID GASKET SEALING
• After removing nuts and bolts, separate the mating surface and
remove old liquid gasket sealing using Tool.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap seal cutter to insert it (1), and then slide it by tapping on the
side (2) as shown.
• In areas where Tool is difficult to use, use plastic hammer to lightly
tap the parts, to remove it.
CAUTION:
If for some unavoidable reason tool such as screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Remove the old liquid gasket adhering to the gasket application
surface and the mating surface using suitable tool.
• Remove liquid gasket completely from the groove of the gas-
ket application surface, bolts, and bolt holes.
2.
Thoroughly clean the mating surfaces and remove adhering
moisture, grease and foreign materials.
Tool number
: KV10112100 (BT-8653-A)
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC0003E
EM-6
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
3.
Attach liquid gasket tube to the Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-26, "Recommended Chemical Products and Sealants"
.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• As for bolt holes, normally apply the liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Make sure to read the text of this manual.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten nuts or bolts after the installation.
• Wait 30 minutes or more after installation, before refilling the
engine with engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
Tool number
: WS39930000 (
—
)
WBIA0567E
SEM159F
PREPARATION
EM-7
< PREPARATION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000001281966
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST0501S000
(
—
)
Engine stand assembly
1. ST05011000
(
—
)
Engine stand
2. ST05012000
(
—
)
Base
Disassembling and assembling engine
—
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room
(Available in SEC. 164 of PARTS CATALOG:
Part No. 16441 6N210)
KV10111100
(J-37228)
Seal cutter
Removing oil pan (lower and upper), front and
rear timing chain case, etc.
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
KV991J0050
(J-44626)
Air fuel sensor Socket
Loosening or tightening air fuel ratio A/F sen-
sor
a: 22 mm (0.87 in)
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 1
a: 22 mm (0.87 in)
NT042
PBIC0198E
NT046
NT052
LBIA0444E
NT636
EM-8
< PREPARATION >
[VQ40DE]
PREPARATION
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2.KV10109220
(
—
)
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-
26336-A), but Part (2) is not so.
KV10107902
(J-38959)
Valve oil seal puller
Replacing valve oil seal
—
(J-39386)
Valve oil seal drift
Installing valve oil seal
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
KV10112100
(BT-8653-A)
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc. in angle
ST16610001
(J-23907)
Pilot bushing puller
Removing pilot converter
Tool number
(Kent-Moore No.)
Tool name
Description
PBIC1650E
NT011
NT024
NT044
NT014
NT045
PREPARATION
EM-9
< PREPARATION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tool
INFOID:0000000001281967
KV991J0120
(J-47128)
Seal installer
Installing rear main seal
KV10117700
(J-44716)
Ring gear stopper
Removing and installing crankshaft pulley
Tool number
(Kent-Moore No.)
Tool name
Description
LBIA0452E
NT822
Tool number
(Kent-Moore No.)
Tool name
Description
(
—
)
Power tool
Loosening nuts and bolts
KV991J0100
(J-46531)
TORX socket
Removing and installing flywheel
Size: T55
(
—
)
Spark plug wrench
Removing and installing spark plug
(J-24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 (0.51) dia.
b: 12 (0.47)
c: 10 (0.39)
Unit: mm (in)
PBIC0190E
PBIC1113E
NT047
NT583
EM-10
< PREPARATION >
[VQ40DE]
PREPARATION
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
(
—
)
Piston ring expander
Removing and installing piston ring
(
—
)
Valve guide drift
Removing and installing valve guide
Intake and Exhaust:
a: 9.5 mm (0.374 in) dia.
b: 5.5 mm (0.217 in) dia.
(
—
)
Valve guide reamer
(1): Reaming valve guide inner hole
(2): Reaming hole for oversize valve guide
Intake and Exhaust:
d
1
: 6.0 mm (0.236 in) dia.
d
2
: 10.175 - 10.196 mm (0.4006 - 0.4014 in)
dia.
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
a: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
b: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
(
—
)
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
(
—
)
Manual lift table caddy
Removing and installing engine
Tool number
(Kent-Moore No.)
Tool name
Description
NT048
NT030
NT015
NT016
AEM488
AEM489
ZZA1210D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст