Nissan Pathfinder (2008 year). Manual — part 126
CHG-20
< SYMPTOM DIAGNOSIS >
CHARGING SYSTEM
SYMPTOM DIAGNOSIS
CHARGING SYSTEM
Symptom Table
INFOID:0000000001712771
Symptom
Reference
Battery discharged
Refer to
.
The charge warning lamp does not illuminate when the ignition
switch is set to ON.
The charge warning lamp does not turn OFF after the engine
starts.
The charging warning lamp turns ON when increasing the engine
speed.
CHG
GENERATOR
CHG-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ON-VEHICLE REPAIR
GENERATOR
Removal and Installation
INFOID:0000000001283043
VQ40DE MODELS
Removal
1.
Disconnect the negative battery terminal.
2.
Remove the fan shroud. Refer to
CO-16, "Removal and Installation"
3.
Remove the drive belt. Refer to
EM-13, "Removal and Installation"
.
4.
Remove the generator stay, using power tools.
5.
Remove the generator upper bolt, using power tools.
6.
Disconnect the generator harness connectors.
7.
Remove the generator.
Installation
Installation is in the reverse order of removal.
• Install the generator and check the tension of the drive belt. Refer to
.
CAUTION:
Tighten terminal "1" nut carefully.
• For this model, the power generation variable voltage control system that controls the power generation volt-
age of the generator has been adopted. Therefore, the power generation variable voltage control system
inspection should be performed after replacing the generator in order to ensure that the system operates
normally.
VK56DE MODELS
1.
Generator
2.
Engine block
3.
Generator stay
WKIA3191E
Terminal "1" nut
: 10.8 N·m (1.1 kg-m, 8 ft-lb)
CHG-22
< ON-VEHICLE REPAIR >
GENERATOR
Removal
1.
Disconnect the negative battery terminal.
2.
Remove the air dam using power tool.
3.
Remove the engine undercover using power tool.
4.
Remove the fan shroud.
5.
Remove the drive belt. Refer to
EM-153, "Removal and Installation"
.
6.
Remove the lower bracket, using power tools.
7.
Remove the generator upper bolt, using power tools.
8.
Disconnect the generator harness connectors.
9.
Remove the generator.
Installation
Installation is in the reverse order of removal.
• Install the generator and check the tension of the drive belt. Refer to
EM-153, "Checking Drive Belts"
CAUTION:
Tighten terminal "1" nut carefully.
• For this model, the power generation variable voltage control system that controls the power generation volt-
age of the generator has been adopted. Therefore, the power generation variable voltage control system
inspection should be performed after replacing the generator in order to ensure that the system operates
normally.
GENERATOR PULLEY INSPECTION
Perform the following.
• Make sure that the generator pulley does not rattle.
• Make sure that the generator pulley nut is properly tightened.
WKIA1390E
Terminal "1" nut
: 10.8 N·m (1.1 kg-m, 8 ft-lb)
Generator pulley nut
: 118 N·m (12.0 kg-m, 87 ft-lb)
CHG
SERVICE DATA AND SPECIFICATIONS (SDS)
CHG-23
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Generator
INFOID:0000000001281941
Type
LR1130-701
Valeo
Engine
VQ40DE/VK56DE
Nominal rating
12V-130A
Ground polarity
Negative
Minimum revolution under no-load (When 13.5
volts is applied)
1,200 rpm
Hot output current (When 13.5 volts is applied)
More than 82A/1800rpm
More than 115A/2,500rpm
More than 130A/5,000rpm
Regulated output voltage
14.1 - 14.7V @ 20
°
C
Adjustment range of power generation variable
voltage control
11.4 - 15.6V
CO-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
CO
A
CO
N
O
P
CONTENTS
ENGINE COOLING SYSTEM
VQ40DE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Liquid Gasket . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
FUNCTION DIAGNOSIS . . . . . . . ...
COOLING SYSTEM . . . . . . . . . . .
Cooling Circuit . . . . . . . . . . . . . . ...
Schematic . . . . . . . . . . . . . . . .....
OVERHEATING CAUSE ANALYSIS . . . . ..
Troubleshooting Chart . . . . . . . . . . . ...
ON-VEHICLE MAINTENANCE . . . . .
ENGINE COOLANT . . . . . . . . . . ...
System Inspection . . . . . . . . . . . . ...
Changing Engine Coolant . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . .
RADIATOR . . . . . . . . . . . . . . .
Components . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Checking Radiator . . . . . . . . . . . . ...
ENGINE COOLING FAN . . . . . . . . .
Removal and Installation (Crankshaft driven type)
Removal and Installation (Motor driven type) . . ..
WATER PUMP . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
WATER INLET AND THERMOSTAT ASSEM-
BLY . . . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
WATER OUTLET AND WATER PIPING . . ..
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Standard and Limit . . . . . . . . . . . . ..
VK56DE
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Precaution for Liquid Gasket . . . . . . . . ...
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tool . . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
FUNCTION DIAGNOSIS . . . . . . . ..
COOLING SYSTEM . . . . . . . . . . ..
Cooling Circuit . . . . . . . . . . . . . . .
Schematic . . . . . . . . . . . . . . . .
OVERHEATING CAUSE ANALYSIS . . . .
Troubleshooting Chart . . . . . . . . . . . .
ON-VEHICLE MAINTENANCE . . . . .
CO-2
System Inspection . . . . . . . . . . . . ..
Changing Engine Coolant . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . .
RADIATOR . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . ....
Checking Radiator . . . . . . . . . . . . ..
ENGINE COOLING FAN . . . . . . . . ...
Removal and Installation (Crankshaft Driven
Type) . . . . . . . . . . . . . . . . . ..
Removal and Installation (Motor Driven Type) . ...
WATER PUMP . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
THERMOSTAT AND WATER PIPING . . . ..
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
PRECAUTIONS
CO-3
< PRECAUTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001315964
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Liquid Gasket
INFOID:0000000001282185
REMOVAL OF LIQUID GASKET SEALING
• After removing nuts and bolts, separate the mating surface, using Tool and remove old liquid gasket sealing.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap Tool to insert it, and then slide it by tapping on the side as
shown.
• In areas where Tool is difficult to use, use plastic hammer to lightly
tap the parts, to remove it.
CAUTION:
If for some unavoidable reason suitable tool such as screw-
driver is used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Remove the old liquid gasket adhering to the gasket application
surface and the mating surface using suitable tool.
• Remove the liquid gasket completely from the groove of the
liquid gasket application surface, bolts, and bolt holes.
2.
Thoroughly clean the mating surfaces and remove adhering
moisture, grease and foreign material.
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC0003E
CO-4
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
3.
Attach the liquid gasket tube to the Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-26, "Recommended Chemical Products and Sealants"
.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• As for the bolt holes, normally apply the liquid gasket inside
the holes. If specified in the procedure, it should also be
applied outside the holes.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• Wait 30 minutes or more after installation before refilling the
engine with engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
Tool number
: WS39930000 (
—
)
WBIA0567E
SEM159F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст