Nissan Pathfinder (2008 year). Manual — part 173
BACK DOOR CONTROL UNIT
DLK-285
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR CONTROL UNIT
Reference Value
INFOID:0000000001728558
TERMINAL LAYOUT
PHYSICAL VALUES
ALKIA1246ZZ
Terminal
Wire Col-
or
Item
Condition
Voltage (V)
(Approx.)
1
R/B
Battery power supply
—
Battery voltage
2
Y
Back door cinching latch unit
motor
Back door closing
Battery voltage
Back door opening
0
3
L
Back door cinching latch unit
motor
Back door closing
0
Back door opening
Battery voltage
4
B
Ground
—
—
5
GR
Door lock sensor output
RF door door lock UNLOCKED
0
RF door door lock LOCKED
Battery voltage
6
G
Back door release switch output
Back door release switch ON
0
Back door release switch OFF
Battery voltage
7
BR
Half switch signal
Back door open
0
Back door closed or latching
Battery voltage
8
P
Close switch signal
Back door open or closed
Battery voltage
During opening (5 seconds)
0
9
W
Neutral switch signal
Back door open or closed
Battery voltage
During opening (5 seconds)
0
DLK-286
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR CONTROL UNIT
Wiring Diagram—BACK DOOR OPENER—
INFOID:0000000001728559
ALKWA0147GB
BACK DOOR CONTROL UNIT
DLK-287
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ALKIA0991GB
DLK-288
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR CONTROL UNIT
ALKIA0992GB
BACK DOOR CONTROL UNIT
DLK-289
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ALKIA0993GB
DLK-290
< ECU DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR CONTROL UNIT
Fail Safe
INFOID:0000000001728560
Fail-safe operation
The back door system operation will be interrupted if the back door control unit loses power.
ALKIA0994GB
DOOR LOCK
DLK-291
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYMPTOM DIAGNOSIS
DOOR LOCK
Symptom Table
INFOID:0000000001563757
DOOR LOCK SYSTEM
NOTE:
• Before performing the diagnosis in the following table, check “Work flow”. Refer to
• If the following symptoms” are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Symptom
Repair order
Refer to page
Key reminder door function does not operate
properly.
1. Door switch check
2. Key switch (Insert) check
3. Replace BCM.
Power door lock does not operate with door lock
and unlock switch on main power window and
door lock/unlock switch or power window and
door lock/unlock switch RH.
1. Door lock/unlock switch check (driver side)
2. Door lock/unlock switch check (passenger side)
Specific door lock actuator does not operate.
1. Door lock actuator check (Front LH)
2. Door lock actuator check (Front RH)
3. Door lock actuator check (Rear LH)
4. Door lock actuator check (Rear RH)
5. Back door
Power door lock does not operate with front door
key cylinder LH operation.
1. Front door lock assembly LH (key cylinder
switch) check
2. Replace BCM.
Power door lock does not operate.
1. BCM power supply and ground circuit check
2. Door lock/unlock switch check (driver)
3. Door lock/unlock switch check (passenger)
DLK-292
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM
REMOTE KEYLESS ENTRY SYSTEM
Symptom Table
INFOID:0000000001563758
REMOTE KEYLESS ENTRY SYSTEM
Symptom
Diagnoses/service procedure
Reference
page
All functions of remote keyless entry system do not
operate.
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Check BCM and remote keyless entry receiver.
The new ID of keyfob cannot be entered.
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Key switch (insert) check
3. Door switch check
4. ACC power check
5. Replace BCM.
Door lock or unlock does not function.
(If the power door lock system does not operate
manually, check power door lock system)
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Replace BCM.
Hazard and horn reminder does not activate properly
when pressing lock or unlock button of keyfob.
1. Check hazard and horn reminder mode with CONSULT-III
NOTE:
Hazard and horn reminder mode can be changed.
First check the hazard and horn reminder mode setting.
2. Door switch check
3. Replace BCM.
Hazard reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Horn reminder OK)
1. Check hazard reminder mode with CONSULT-III
NOTE:
Hazard reminder mode can be changed.
First check the hazard reminder mode setting.
2. Check hazard function with hazard switch
—
3. Replace BCM.
Horn reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Hazard reminder OK)
1. Check horn reminder mode with CONSULT-III
NOTE:
Horn reminder mode can be changed.
First check the horn reminder mode setting.
2. Check horn function with horn switch
—
3. IPDM E/R operation check
4. Replace BCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст