Qashqai J11. Rear axle — part 1
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
2WD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR WHEEL HUB AND HOUSING . . . . .
Exploded View . . . . . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR WHEEL HUB . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ...
Wheel Bearing . . . . . . . . . . . . . . ...
4WD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ..
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ..
Special Service Tool . . . . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . .
REAR WHEEL HUB AND HOUSING . . . ...
Exploded View . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
REAR WHEEL HUB AND HOUSING . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
RAX-2
< SYMPTOM DIAGNOSIS >
[2WD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010297896
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
NVH in RAX and RSU sections
NVH in WT
section
NVH in WT
section
NVH in BR
section
Possible cause and SUSPECTED PARTS
Im
pro
per in
st
a
lla
ti
on
,
lo
os
en
es
s
Part
s int
e
rference
Whe
e
l be
ari
n
g
da
m
age
REAR AXLE AND RE
AR SUSPENSI
ON
TIRE
ROA
D
WHEEL
BRAKE
Symptom
RAER AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
REAR WHEEL HUB AND HOUSING
RAX-3
< PERIODIC MAINTENANCE >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010297897
.
Inspection
INFOID:0000000010297898
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub, and make sure there is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
RAX-4
< REMOVAL AND INSTALLATION >
[2WD]
REAR WHEEL HUB
REMOVAL AND INSTALLATION
REAR WHEEL HUB
Exploded View
INFOID:0000000010297899
Removal and Installation
INFOID:0000000010481080
REMOVAL
Wheel Hub and Bearing
1.
Remove the wheel and tire using power tool. Refer to
WT-60, "Wheel Balance Adjustment (Aluminum
.
2.
Remove the bolt and separate the rear wheel sensor from the wheel hub and bearing. Refer to
"REAR WHEEL SENSOR : Removal and Installation"
.
CAUTION:
• Failure to separate the rear wheel sensor from the wheel hub and bearing may result in damage
to the rear wheel sensor.
• Pull out the rear wheel sensor, being careful to turn it as little as possible. Never pull on wheel
sensor harness.
3.
Remove torque member bolts using power tool, leaving the brake hose attached. Position brake caliper
aside with wire. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Put alignment marks on the disc brake rotor and on the wheel hub and bearing. Remove the disc brake
rotor. Remove disc brake rotor.
CAUTION:
Never drop disc brake rotor.
5.
Remove the hub bolts and the wheel hub and bearing.
1.
Suspension arm
2.
Back plate
3.
Wheel hub and bearing assembly
Refer to
for symbols in the figure.
E1DIA0225GB
REAR WHEEL HUB
RAX-5
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
6.
If necessary, remove the wheel studs (1) from the wheel hub
and bearing using a suitable tool (A).
CAUTION:
• Remove the wheel studs only when necessary.
• Never hammer the wheel studs or damage to the wheel
hub and bearing may occur.
• Pull out the wheel studs in a direction perpendicular to
the wheel hub and bearing.
INSTALLATION
Installation is in the reverse order of removal.
• Place a washer (A) as shown to install the wheel studs (1) by using
the tightening force of the nut (B).
CAUTION:
• Never reuse the wheel stud.
• Check that there is no clearance between the wheel stud
and the wheel hub and bearing.
• Before installing, make sure there is no foreign material
such as iron fragments adhered to the pick-up part of the
rear wheel sensor.
• When installing, make sure there is no foreign material such
as iron fragments on and in the hole in the wheel hub and
bearing for the rear wheel sensor. Make sure no foreign
material has been caught in the sensor rotor. Remove any foreign material and clean the mount.
• Install the rear wheel sensor to the wheel hub and bearing. Refer to
.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Check that the wheel hub and bearing operates smoothly.
• Perform the inspection after installation. Refer to
Inspection
INFOID:0000000010297901
INSPECTION AFTER REMOVAL
Check wheel hub and bearing assembly for wear, cracks, and damage. Replace if there are.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
JPDIF0299ZZ
JPDIF0300ZZ
RAX-6
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010297902
Axial end play
0.05 mm (0.002 in) or less
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-7
< SYMPTOM DIAGNOSIS >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010297903
Use chart below you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in DLN section
NVH in DLN section
NVH in RAX
and RSU
sections
Refer to REAR AXLE i
n
t
h
is chart
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
o
in
t an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Im
b
a
lanc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
loo
s
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
ROAD W
H
EEL
DRIV
E
SHAFT
BR
AK
E
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
RAX-8
< PRECAUTION >
[4WD]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000010297904
CAUTION:
Note the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a dust-free location.
• Before disassembling and assembling, clean the parts.
• Prevent the entry of foreign objects during disassembly of the service location.
• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a
clean cover must be placed over parts.
• Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint
adhering to parts.
• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be
removed by blowing with air or wiping with paper shop cloths.
PREPARATION
RAX-9
< PREPARATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010297905
Tool number
Tool name
Description
KV38100500
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing sensor rotor
KV40101840
Collar
a: 67 mm (2.64 in) dia.
b: 85 mm (3.35 in) dia.
Installing sensor rotor
ZZA0701D
ZZA1113D
RAX-10
< PERIODIC MAINTENANCE >
[4WD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010297906
Inspection
INFOID:0000000010297907
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub, and make sure there is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
REAR DRIVE SHAFT
RAX-11
< PERIODIC MAINTENANCE >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Inspection
INFOID:0000000010297908
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occur from drive shaft.
RAX-12
< REMOVAL AND INSTALLATION >
[4WD]
REAR WHEEL HUB AND HOUSING
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010297909
Removal and Installation
INFOID:0000000010297910
REMOVAL
Wheel Hub and Bearing Assembly
1.
Remove tires from vehicle.
2.
Remove torque member mounting bolts. Hang torque member not to interfere with work. Refer to
"BRAKE CALIPER ASSEMBLY : Exploded View"
(LHD),
BR-86, "BRAKE CALIPER ASSEMBLY :
(RHD).
CAUTION:
Never depress brake pedal while brake caliper is removed.
3.
Remove disc rotor.
4.
Remove cotter pin, and then loosen hub lock nut.
5.
Patch hub lock nut with a piece of wood. Hammer the wood to
disengage wheel hub and bearing assembly from drive shaft.
Remove the hub lock nut.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never drop drive shaft. Support drive shaft by housing,
joint sub-assembly, shaft etc.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
6.
Remove wheel hub and bearing assembly.
INSTALLTION
Install in the reverse order of removal.
1.
Axle housing
2.
Suspension arm
3.
Back plate
4.
Wheel hub and bearing assembly
5.
Cotter pin
Refer to
for symbols in the figure.
E1DIA0226GB
JPDIF0003ZZ
REAR WHEEL HUB AND HOUSING
RAX-13
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
Inspection
INFOID:0000000010297911
INSPECTION AFTER REMOVAL
Check wheel hub and bearing assembly for wear, cracks, and damage. Replace if there are.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
RAX-14
< REMOVAL AND INSTALLATION >
[4WD]
REAR DRIVE SHAFT
REAR DRIVE SHAFT
Exploded View
INFOID:0000000010297912
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000010297913
REMOVAL
1.
Remove tires from vehicle.
2.
Remove torque member mounting bolts. Hang torque member not to interfere with work. Refer to
"BRAKE CALIPER ASSEMBLY : Exploded View"
(LHD),
BR-86, "BRAKE CALIPER ASSEMBLY :
(RHD).
CAUTION:
Never depress brake pedal while brake caliper is removed.
1.
Drive shaft
2.
Cotter pin
Refer to
for symbols in the figure.
PDIA1172J
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Boot band
7.
Boot
8.
Shaft
9.
Circular clip
10. Joint sub-assembly
11.
Sensor rotor
: Wheel side
: Fill NISSAN genuine grease or an equivalent.
Refer to
for symbols not described on the above.
JPDIG0015ZZ
REAR DRIVE SHAFT
RAX-15
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
3.
Remove disc rotor.
4.
Remove cotter pin, then loosen hub lock nut.
5.
Patch hub lock nut with a piece of wood. Hammer the wood to
disengage wheel hub and bearing assembly from drive shaft.
Remove the hub lock nut.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
housing (or joint sub-assembly), shaft and the other parts.
NOTE:
Using a suitable puller if the wheel hub and bearing assembly
and drive shaft cannot be separated even after performing the
above procedure.
6.
Remove wheel sensor from axle housing. Refer to
BRC-139, "REAR WHEEL SENSOR : Exploded
.
7.
Remove stabilizer link. Refer to
8.
Set suitable jack under suspension arm.
9.
Remove shock absorber from suspension arm. Refer to
10. Remove upper link from suspension arm. Refer to
11. Remove lower link from suspension arm. Refer to
.
12. Remove drive shaft from final drive assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at suspension arm (rubber bushing), under unladen conditions with
tires on level ground.
Disassembly and Assembly
INFOID:0000000010297914
DISASSEMBLY
Final Drive Side
1.
Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Remove boot bands, and then remove boot from housing.
3.
Put matching marks on housing and shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never scratch the surface.
4.
Put matching marks (A) on the spider assembly and shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never
scratch the surface.
JPDIF0003ZZ
JPDIF0006ZZ
RAX-16
< REMOVAL AND INSTALLATION >
[4WD]
REAR DRIVE SHAFT
5.
Remove snap ring (1), and then remove spider assembly from
shaft.
6.
Remove boot from shaft.
7.
Remove circular clip housing.
8.
Remove dust shield to housing.
9.
Remove old grease on housing with paper towels.
Wheel Side
1.
If sensor rotor needs to be removed, use a bearing replacer (A)
and puller (B). Refer to
Removal and Installation - Rear Sensor Rotor"
.
2.
Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
3.
Remove boot bands. Then remove boot from joint sub-assembly.
4.
Screw the drive shaft puller (A) 30 mm (1.18 in) or more into the
thread of joint sub-assembly, and pull joint sub-assembly with a
sliding hammer (B) from shaft.
CAUTION:
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
• Align sliding hammer and drive shaft and remove them by
pulling directory.
5.
Remove boot from shaft.
6.
Remove circular clip.
CAUTION:
Never reuse circular clip.
7.
While rotating ball cage, clean old grease on joint sub-assembly with paper towels.
ASSEMBLY
Final drive Side
1.
Wrap serrated part of shaft with tape (A). Install boot band and
boot to shaft. Be careful not to damage boot.
CAUTION:
Never reuse boot and boot band.
2.
Remove the tape wrapped around the serrated on shaft.
JPDIF0014ZZ
JPDIG0016ZZ
JPDIF0015ZZ
JPDIF0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст