Nissan GT-R (2007-2014 year). METER, WARNING LAMP & INDICATOR. Service Manual — part 2
MWI
METER SYSTEM
MWI-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FUEL GAUGE : Component Parts Location
INFOID:0000000009189308
1.
Fuel level sensor unit
(Sub)
2.
Fuel level sensor unit
(Main)
3.
Door switch (passenger side)
4.
Oil pressure sensor
5.
Ambient sensor
6.
Oil level sensor
7.
Washer level switch
8.
AWD control unit
9.
Brake fluid level switch
JPNIA1142ZZ
Revision: 2012 November
2014 GT-R
MWI-18
< SYSTEM DESCRIPTION >
METER SYSTEM
FUEL GAUGE : Component Description
INFOID:0000000009189309
ODO/TRIP METER
ODO/TRIP METER : System Diagram
INFOID:0000000009189310
ODO/TRIP METER : System Description
INFOID:0000000009189311
• ABS actuator control unit reads the rectangular wave signal received from wheel sensor, and transmits the
vehicle speed signal to the combination meter via CAN communication.
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication, then calculates and displays the travel distance.
10. ABS actuator and electric unit (con-
trol unit)
11. Door switch (driver side)
12. TCM
13. Trunk switch
14. Combination meter
15. Combination switch (Lighting switch)
16. Low tire pressure warning control unit 17. Parking brake
18. BCM
19. ECM
A.
Under rear seat
B.
Right side of engine
C.
Radiator core support (center)
D.
Oil pan LH upper
E.
Front RH seat under
F.
Trunk room left back
G.
Lower instrument panel LH
H.
Dashboard side lower (passenger
seat side)
I.
Glove box assembly back
Unit
Description
Combination meter
Reads the fuel level sensor signal (resistance value) from the fuel level sensor unit, and indicates
the remaining fuel level.
Fuel level sensor unit
Detects the fuel level in fuel tank using the fuel level sensor unit, and transmits the fuel level sen-
sor signal to the combination meter.
JPNIA1015GB
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ODO/TRIP METER : Component Parts Location
INFOID:0000000009189312
1.
Fuel level sensor unit
(Sub)
2.
Fuel level sensor unit
(Main)
3.
Door switch (passenger side)
4.
Oil pressure sensor
5.
Ambient sensor
6.
Oil level sensor
7.
Washer level switch
8.
AWD control unit
9.
Brake fluid level switch
JPNIA1142ZZ
Revision: 2012 November
2014 GT-R
MWI-20
< SYSTEM DESCRIPTION >
METER SYSTEM
ODO/TRIP METER : Component Description
INFOID:0000000009189313
SHIFT POSITION INDICATOR
SHIFT POSITION INDICATOR : System Diagram
INFOID:0000000009189314
SHIFT POSITION INDICATOR : System Description
INFOID:0000000009189315
• The combination meter receives the shift position signal from TCM via CAN communication, and displays
the shift position to the shift position indicator.
• The combination meter receives the shift position signal from TCM via CAN communication. If the status
does not allow a shift change, it blinks the shift position indicator.
10. ABS actuator and electric unit (con-
trol unit)
11. Door switch (driver side)
12. TCM
13. Trunk switch
14. Combination meter
15. Combination switch (Lighting switch)
16. Low tire pressure warning control unit 17. Parking brake
18. BCM
19. ECM
A.
Under rear seat
B.
Right side of engine
C.
Radiator core support (center)
D.
Oil pan LH upper
E.
Front RH seat under
F.
Trunk room left back
G.
Lower instrument panel LH
H.
Dashboard side lower (passenger
seat side)
I.
Glove box assembly back
Unit
Description
Combination meter
Converts the vehicle speed signal received from the ABS actuator and electric unit (control unit)
via CAN communication to mileage, and displays the accumulated mileage to the odometer and
tripmeter.
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter via CAN communication.
JPNIA1146GB
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SHIFT POSITION INDICATOR : Component Parts Location
INFOID:0000000009189316
1.
Fuel level sensor unit
(Sub)
2.
Fuel level sensor unit
(Main)
3.
Door switch (passenger side)
4.
Oil pressure sensor
5.
Ambient sensor
6.
Oil level sensor
7.
Washer level switch
8.
AWD control unit
9.
Brake fluid level switch
JPNIA1142ZZ
Revision: 2012 November
2014 GT-R
MWI-22
< SYSTEM DESCRIPTION >
METER SYSTEM
SHIFT POSITION INDICATOR : Component Description
INFOID:0000000009189317
OIL PRESSURE WARNING LAMP
OIL PRESSURE WARNING LAMP : System Diagram
INFOID:0000000009189318
OIL PRESSURE WARNING LAMP : System Description
INFOID:0000000009189319
OIL PRESSURE WARNING LAMP
Control Outline
The combination meter reads the oil pressure sensor signal from oil pressure sensor, and illuminates/turns off
the oil pressure warning lamp.
NOTE:
The display of engine oil pressure warning on the information display is shown/turned off simultaneously with
the illumination/turning off of the oil pressure warning lamp.
10. ABS actuator and electric unit (con-
trol unit)
11. Door switch (driver side)
12. TCM
13. Trunk switch
14. Combination meter
15. Combination switch (Lighting switch)
16. Low tire pressure warning control unit 17. Parking brake
18. BCM
19. ECM
A.
Under rear seat
B.
Right side of engine
C.
Radiator core support (center)
D.
Oil pan LH upper
E.
Front RH seat under
F.
Trunk room left back
G.
Lower instrument panel LH
H.
Dashboard side lower (passenger
seat side)
I.
Glove box assembly back
Unit
Description
Combination meter
• Receives the shift position signal from TCM via CAN communication, and displays the shift po-
sition to the shift position indicator.
• Receives the shift position signal from TCM via CAN communication, and if the status does not
allow a shift change, it blinks the shift position display in the shift position indicator.
TCM
Transmits the shift position signal to the combination meter via CAN communication.
JPNIA1144GB
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
OIL PRESSURE WARNING LAMP : Component Parts Location
INFOID:0000000009189320
1.
Fuel level sensor unit
(Sub)
2.
Fuel level sensor unit
(Main)
3.
Door switch (passenger side)
4.
Oil pressure sensor
5.
Ambient sensor
6.
Oil level sensor
7.
Washer level switch
8.
AWD control unit
9.
Brake fluid level switch
JPNIA1142ZZ
Revision: 2012 November
2014 GT-R
MWI-24
< SYSTEM DESCRIPTION >
METER SYSTEM
OIL PRESSURE WARNING LAMP : Component Description
INFOID:0000000009189321
METER ILLUMINATION CONTROL
METER ILLUMINATION CONTROL : System Diagram
INFOID:0000000009189322
METER ILLUMINATION CONTROL : System Description
INFOID:0000000009189323
METER ILLUMINATION CONTROL FUNCTION
Every time when the illumination control switch (1) is pressed, the
illuminance of meter illumination can be adjusted in 22 steps. (Illumi-
nance can be adjusted both in daytime and nighttime modes.)
10. ABS actuator and electric unit (con-
trol unit)
11. Door switch (driver side)
12. TCM
13. Trunk switch
14. Combination meter
15. Combination switch (Lighting switch)
16. Low tire pressure warning control unit 17. Parking brake
18. BCM
19. ECM
A.
Under rear seat
B.
Right side of engine
C.
Radiator core support (center)
D.
Oil pan LH upper
E.
Front RH seat under
F.
Trunk room left back
G.
Lower instrument panel LH
H.
Dashboard side lower (passenger
seat side)
I.
Glove box assembly back
Unit
Description
Combination meter
Using the oil pressure sensor signal received from oil pressure sensor, illuminates/turns off the oil
pressure warning lamp.
Oil pressure sensor
Detects the oil pressure of engine oil, and transmits the oil pressure sensor signal to the combi-
nation meter.
JPNIA1147GB
NNNIA0018ZZ
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER ILLUMINATION CONTROL : Component Parts Location
INFOID:0000000009189324
1.
Fuel level sensor unit
(Sub)
2.
Fuel level sensor unit
(Main)
3.
Door switch (passenger side)
4.
Oil pressure sensor
5.
Ambient sensor
6.
Oil level sensor
7.
Washer level switch
8.
AWD control unit
9.
Brake fluid level switch
JPNIA1142ZZ
Revision: 2012 November
2014 GT-R
MWI-26
< SYSTEM DESCRIPTION >
METER SYSTEM
METER ILLUMINATION CONTROL : Component Description
INFOID:0000000009189325
INFORMATION DISPLAY
INFORMATION DISPLAY : System Diagram
INFOID:0000000009189326
INFORMATION DISPLAY : System Description
INFOID:0000000009189327
DESCRIPTION
10. ABS actuator and electric unit (con-
trol unit)
11. Door switch (driver side)
12. TCM
13. Trunk switch
14. Combination meter
15. Combination switch (Lighting switch)
16. Low tire pressure warning control unit 17. Parking brake
18. BCM
19. ECM
A.
Under rear seat
B.
Right side of engine
C.
Radiator core support (center)
D.
Oil pan LH upper
E.
Front RH seat under
F.
Trunk room left back
G.
Lower instrument panel LH
H.
Dashboard side lower (passenger
seat side)
I.
Glove box assembly back
Unit
Description
Combination meter
Controls the meter illumination with the illumination control switch signal from the meter control
switch and the position light request signal from BCM via CAN communication.
BCM
Transmits the position light request signal to the combination meter via CAN communication.
Meter control switch
Transmits the following signals to the combination meter.
• Illumination control switch signal (+)
• Illumination control switch signal (-)
Combination switch
(Lighting switch)
Using the combination switch reading function, BCM reads the combination switch status.
JPNIA1145GB
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The combination meter inputs the information required to control the operation of information display by
using the communication signals and others from each unit.
• The combination meter integrates the drive computer function, and performs the warning display/information
display by using the signals received from each unit, sensor, and switch.
• When the enter switch signal or select switch signal is received, the combination meter can check, change
screens, perform setting, or reset the warning, indication, information, and setting on the information display.
INSTANTANEOUS FUEL CONSUMPTION
Control Outline
• The combination meter receives the fuel consumption monitor signal from ECM and the vehicle speed signal
from the ABS actuator control unit via CAN communication.
• Based on the fuel consumption monitor signal and vehicle speed signal that are received via CAN communi-
cation, the combination meter calculates the instantaneous fuel consumption, and displays the result.
VEHICLE SPEED
Control Outline
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
• Based on the vehicle speed signal received via CAN communication, the combination meter displays the
vehicle speed.
CRUISE CONTROL SYSTEM STATUS
Control Outline
• The combination meter receives the ASCD status signal from ECM via CAN communication.
• Based on the ASCD status signal received via CAN communication, the combination meter displays the
CRUISE control system setting status.
NOTE:
When the CRUISE control system is OFF, the CRUISE control system status is not displayed.
AVERAGE FUEL CONSUMPTION
Control Outline
• The combination meter receives the fuel consumption monitor signal from ECM and the vehicle speed signal
from the ABS actuator control unit via CAN communication.
• Based on the fuel consumption monitor signal and vehicle speed signal that are received via CAN communi-
cation, the combination meter calculates the average fuel consumption, and displays the result.
• The average fuel consumption displayed on the information display is updated at approximately 30-second
intervals.
NOTE:
“
−−−−
” is displayed for approximately 30 seconds just after the reset operation and after the ignition switch is
OFF
→
ON. It is displayed simultaneously until the vehicle is driven approximately 500 m (0.3 mile).
AVERAGE VEHICLE SPEED
Control Outline
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
• Based on the vehicle speed signal received via CAN communication and on the travel time measured in
combination meter, the combination meter calculates the average vehicle speed, and displays the result.
• The average vehicle speed displayed on the information display is updated at approximately 30-second
intervals.
NOTE:
“
−−−−
” is displayed for 30 seconds just after the reset operation and after the ignition switch is OFF
→
ON. It is
displayed simultaneously until the vehicle is driven approximately 500 m (0.3 mile).
TRAVEL TIME
Control Outline
The combination meter measures and displays travel time (ignition switch ON time).
TRAVEL DISTANCE
Control Outline
Revision: 2012 November
2014 GT-R
MWI-28
< SYSTEM DESCRIPTION >
METER SYSTEM
The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control unit)
via CAN communication, then calculates and displays the travel distance.
POSSIBLE DRIVING DISTANCE
Control Outline
• The combination meter receives the fuel consumption monitor signal from ECM and the vehicle speed signal
from the ABS actuator control unit via CAN communication.
• Based on the signal received via CAN communication and on the fuel level sensor signal received from the
fuel level sensor unit, the combination meter calculates the possible driving distance, and displays the result.
NOTE:
• “
−−−−
” is displayed for 30 seconds after the ignition switch is OFF
→
ON. It is displayed simultaneously until
the vehicle is driven approximately 500 m (0.3 mile).
• The indicated values may not match each other when refueling with the ignition switch ON. Refer to
"FUEL GAUGE : System Description"
AMBIENT AIR TEMPERATURE
• Combination meter calculates outside air temperature based on the signal received from ambient sensor,
and displays the result on information display.
• Combination meter corrects the indicated temperature using ignition switch signal, ambient sensor signal
and vehicle speed signal.
Correction Process (Right after ignition switch is turned ON)
The detected temperature by ambient sensor is displayed when the vehicle enters in both of the following con-
dition.
• When the detected temperature is higher than the indicated temperature on information display.
• When the duration of ignition switch OFF to ON is long.
The last indicated temperature is displayed when the vehicle enters in either of the following conditions.
• When the detected temperature by ambient sensor is lower than the indicated temperature on information
display.
• When the duration of ignition switch OFF to ON is short.
Correction Process (When the ignition switch is ON)
The detected temperature by ambient sensor is displayed under the following condition.
• When the detected temperature is lower than the indicated temperature on information display.
The indicated temperature is not updated under the following condition.
• When the detected temperature by ambient sensor is higher than the indicated temperature on information
display [at a speed of 20 km/h (12 MPH) or less].
The indicated temperature on information display rises slowly to reach the detected temperature by ambient
sensor under the following condition.
• When the detected temperature is higher than the indicated temperature on information display [at a speed
of more than 20 km/h (12 MPH)].
The indicated temperature on information display rises to reach the detected temperature by ambient sensor
under the following condition.
• When the detected temperature is higher than the indicated temperature on information display [while driv-
ing a certain period of time at a speed of more than 20 km/h (12 MPH)].
NOTE:
• “
−−−−
” is displayed for 2.5 seconds right after ignition switch is turned ON.
• If a battery or combination meter is removed and installed, the detected temperature by ambient sensor is
displayed, right after ignition switch is turned ON.
• The indicated temperature may be higher than the actual temperature because of heat radiation from engine
or reflection of heat on road surface.
SETTING
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-29
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Setting item list
NOTE:
Engine oil level display
Items
Setting range
Setting unit
(Press and
hold for 1
second or
more)
Description
Alert
Up shift
AUTO, OFF, 3000 rpm –
6300 rpm
100 rpm
(500 rpm)
The engine speed signal is re-
ceived from ECM via CAN commu-
nication, and the up-shift indicator
can be set to ON/blink/OFF de-
pending on the engine speed.
Timer
OFF, 0.5HOUR–
6HOUR
30 minutes
(60 minutes)
An alarm message is displayed on
the information display when the
set travel time is reached.
ICY
ON/OFF
—
When the ambient air temperature
becomes 3
°
C (37
°
F) or lower, the
ambient sensor signal is received
from the ambient sensor and a
freeze caution alarm message is
displayed on the information dis-
play.
Maintenance
Oil
Engine
Replace-
ment dis-
tance
No setting – 15000 km
No setting – 9500 miles
500 km
(1000 km)
250 miles
(500 miles)
• An engine oil replacement dis-
tance warning is displayed on the
information display.
• When the set distance is
reached, a warning is displayed
requesting replacement of the
engine oil.
Remain-
ing amount
—
—
• The oil level sensor signal is re-
ceived from oil level sensor, and
the engine oil level is displayed in
5 steps.
• The oil level sensor signal is re-
ceived from the oil level sensor,
and an indication is displayed
that the engine oil level is at a
normal value.
• The oil level sensor signal is re-
ceived from the oil level sensor,
and an indication is displayed
that the engine oil level is abnor-
mal.
Trans-
mission
Replace-
ment dis-
tance
No setting – 90000 km
No setting – 55500 miles
500 km
(1000 km)
250 miles
(500 miles)
When the set distance is reached, a
warning is displayed requesting re-
placement of the transmission oil.
Filter
Replace-
ment dis-
tance
No setting – 15000 km
No setting – 9500 miles
500 km
(1000 km)
250 miles
(500 miles)
When the set distance is reached, a
warning is displayed requesting re-
placement of the oil filter.
Tire
Replace-
ment dis-
tance
No setting – 30000 km
No setting – 18500 miles
500 km
(1000 km)
250 miles
(500 miles)
When the set distance is reached, a
warning is displayed requesting re-
placement of the tires.
Options
Language
ENGLISH/FRANCAIS
—
—
Changing the language setting can
be performed.
Unit
METRIC/US
—
—
Changing the unit setting can be
performed.
Revision: 2012 November
2014 GT-R
MWI-30
< SYSTEM DESCRIPTION >
METER SYSTEM
When the following conditions are satisfied, the combination meter reads the resistance value of oil level sen-
sor, and displays the oil level on the information display. The combination meter does not read the oil level
sensor resistance value within 5 minutes after the previous reading of oil level sensor resistance value by the
combination meter.
1.
Turn the ignition switch OFF.
2.
Wait for 5 minutes or more, then open the driver door.
DOOR OPEN WARNING
Control Outline
The combination meter receives the door switch signal from BCM via CAN communication, then judges and
displays the door open warning.
TRUNK OPEN WARNING
Control Outline
The combination meter receives the trunk switch signal from BCM via CAN communication, then judges and
displays the trunk open warning.
PARKING BRAKE RELEASE WARNING
Control Outline
Based on the vehicle speed signal received from ABS actuator and electric unit (control unit) via CAN commu-
nication and on the parking brake switch signal received from parking brake switch, the combination meter
judges and displays the parking brake release warning.
Warning Operation Condition
The system judges that the parking brake is not released when the following conditions are satisfied.
• Vehicle speed is 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
LOW FUEL WARNING
Control Outline
• Using the fuel gauge signal sent from the fuel level sensor unit, the combination meter judges and displays
the fuel level warning.
Warning Operation Condition
• Fuel level: Approximately 13.5 (3-5/8 US gal, 3 lmp gal) or less [1.0 (1/4 US gal, 1/4 Imp gal) fuel resi-
dues included].
LOW WASHER FLUID WARNING
Control Outline
• The combination meter receives the washer level switch signal from the washer level switch.
• Based on the received washer level switch signal, the combination meter displays the low washer fluid warn-
ing.
Warning Operation Condition
• The low washer fluid warning is displayed if the washer level switch remains ON for 180 seconds or more.
• Even when the washer level switch is turned OFF while displaying the low washer fluid warning, the warning
remains displayed if it is within 30 seconds.
ENGINE OIL LEVEL SENSOR ABNORMALITY WARNING
Control Outline
JSNIA0033GB
Revision: 2012 November
2014 GT-R
MWI
METER SYSTEM
MWI-31
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Under the following conditions, the combination meter displays the oil level sensor warning.
• Oil level sensor is open (resistance value of oil level sensor signal circuit exceeds 20
Ω
).
• Oil level sensor is shorted (resistance value of oil level sensor signal circuit is less than 3
Ω
).
SHIFT LEVER POSITION WARNING
Control Outline
• The combination meter receives the shift lever position warning display signal from TCM via CAN communi-
cation.
• Based on the shift lever position warning display signal received via CAN communication, the combination
meter displays the shift lever position warning.
SHIFT “ P ” WARNING
Control Outline
• The combination meter receives the shift lever position check display signal from TCM via CAN communica-
tion.
• Based on the shift lever position check display signal received via CAN communication, the combination
meter displays the shift “ P ” warning.
TRANSMISSION SYSTEM CHECK
Control Outline
• The combination meter receives the transmission system check display signal from TCM via CAN communi-
cation.
• Based on the transmission system check display signal received via CAN communication, the combination
meter displays the transmission system check.
RUN-FLAT TIRE WARNING
Control Outline
• The combination meter receives the run-flat tire warning display signal from the low tire pressure warning
control unit via CAN communication.
• Based on the run-flat tire warning display signal received via CAN communication, the combination meter
displays the run-flat tire warning.
TRANSMISSION CLUTCH HIGH TEMPERATURE WARNING
Control Outline
• The combination meter receives the transmission clutch high temperature warning display signal from TCM
via CAN communication.
• Based on the transmission clutch high temperature warning display signal received via CAN communication,
the combination meter displays the transmission clutch high temperature warning.
TRANSMISSION OIL HIGH TEMPERATURE WARNING
• The combination meter receives the transmission oil high temperature warning display signal from TCM via
CAN communication.
• Based on the transmission oil high temperature warning display signal received via CAN communication, the
combination meter displays the transmission oil high temperature warning.
LOW TIRE PRESSURE WARNING
Control Outline
• The combination meter receives the low tire pressure warning display signal from the low tire pressure warn-
ing control unit via CAN communication.
• Based on the low tire pressure warning display signal received via CAN communication, the combination
meter displays the low tire pressure warning.
AWD CLUTCH HIGH TEMPERATURE WARNING
Control Outline
• The combination meter receives the AWD clutch high temperature warning display signal from the AWD
control unit via CAN communication.
• Based on the AWD clutch high temperature warning display signal received via CAN communication, the
combination meter displays the AWD clutch high temperature warning.
FRONT/REAR TIRE SIZE DISCREPANCY WARNING
Revision: 2012 November
2014 GT-R
MWI-32
< SYSTEM DESCRIPTION >
METER SYSTEM
Control Outline
• The combination meter receives the front/rear tire discrepancy warning display signal from the AWD control
unit via CAN communication.
• Based on the front/rear tire discrepancy warning display signal received via CAN communication, the combi-
nation meter displays the front/rear tire discrepancy warning.
TRANSMISSION SYSTEM WARNING
Control Outline
• The combination meter receives the transmission system warning display signal from TCM via CAN commu-
nication.
• Based on the transmission system warning display signal received via CAN communication, the combination
meter displays the transmission system warning.
TIRE PRESSURE MONITORING SYSTEM WARNING
Control Outline
• The combination meter receives the tire pressure monitoring system warning display signal from the low tire
pressure warning control unit via CAN communication.
• Based on the tire pressure monitoring system warning display signal received via CAN communication, the
combination meter displays the tire pressure monitoring system warning.
AWD SYSTEM WARNING
Control Outline
• The combination meter receives the AWD system warning display signal from the AWD control unit via CAN
communication.
• Based on the AWD system warning display signal received via CAN communication, the combination meter
displays the AWD system warning.
ANTI-LOCK BRAKING SYSTEM (ABS) WARNING
Control Outline
• The combination meter receives the ABS warning display signal from the ABS control unit via CAN commu-
nication.
• Based on the ABS warning display signal received via CAN communication, the combination meter displays
the anti-lock braking system (ABS) warning.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM WARNING
Control Outline
• The combination meter receives the VDC warning display signal from the ABS control unit via CAN commu-
nication.
• Based on the VDC warning display signal received via CAN communication, the combination meter displays
the vehicle dynamic control (VDC) system warning.
ENGINE SYSTEM WARNING
Control Outline
• The combination meter receives the engine status signal from ECM via CAN communication.
• Based on the engine status signal received via CAN communication, the combination meter displays the
engine system warning.
CRUISE CONTROL SYSTEM WARNING
Control Outline
• The combination meter receives the ASCD status signal from ECM via CAN communication.
• Based on the ASCD status signal received via CAN communication, the combination meter displays the
cruise control system warning.
ENGINE OIL LOW PRESSURE WARNING
Control Outline
• The combination meter receives the oil pressure sensor signal from the oil pressure sensor.
• Based on the received oil pressure sensor signal, the combination meter displays the insufficient engine oil
low pressure warning.
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст