Nissan GT-R (2007-2014 year). METER, WARNING LAMP & INDICATOR. Service Manual — part 5
MWI
PRECAUTIONS
MWI-65
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Working Range at a Regular Dealership
INFOID:0000000009189368
CAUTION:
The service items unmentioned on this manual are recommended to be performed by a GT-R certified
NISSAN dealer. Because those service items require special equipment and a GT-R certified technical
staff who completed special training.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009189369
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000009189370
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2012 November
2014 GT-R
MWI-66
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000009189371
Tool name
Description
Power tool
Loosening screws
PBIC0191E
Revision: 2012 November
2014 GT-R
MWI
COMBINATION METER
MWI-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
COMBINATION METER
Exploded View
INFOID:0000000009189372
REMOVAL
Cluster Lid A
.
Combination Meter
DISASSEMBLY
1.
Cluster lid A rear cover
2.
Combination meter
3.
Bracket
4.
Meter housing
5.
Meter control switch
6.
Cluster lid A under cover
7.
Cluster lid A front cover
NNNIA0085ZZ
1.
Meter control unit assembly
2.
Upper housing
3.
Front cover
NNNIA0012ZZ
Revision: 2012 November
2014 GT-R
MWI-68
< REMOVAL AND INSTALLATION >
COMBINATION METER
Removal and Installation
INFOID:0000000009189373
REMOVAL
1.
Remove the cluster lid A from the vehicle. Refer to
IP-13, "Removal and Installation"
.
2.
Remove the meter control switch connector (1) from the combi-
nation meter (2).
3.
Remove the screws (A), and then remove the cluster lid A rear
cover (3).
4.
Remove screws (B).
5.
Remove the screws (A), and then remove the combination
meter (1).
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000009189374
DISASSEMBLY
1.
Remove the tabs, and then remove the upper housing.
2.
Remove the tabs, and then remove the front cover.
ASSEMBLY
Assemble the reverse order of disassembly.
NNNIA0011ZZ
NNNIA0107ZZ
Revision: 2012 November
2014 GT-R
MWI
METER CONTROL SWITCH
MWI-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER CONTROL SWITCH
Exploded View
INFOID:0000000009189375
REMOVAL
.
DISASSEMBLY
Removal and Installation
INFOID:0000000009189376
REMOVAL
1.
Remove the combination meter.
2.
Remove the screws (A), and then remove the cluster lid A front
cover (1).
3.
Remove the screws (A), and then remove the bracket and meter
housing (1).
1.
Bracket
2.
Meter housing
3.
Meter control switch
4.
Cluster lid A under cover
5.
Cluster lid A front cover
NNNIA0110ZZ
NNNIA0109ZZ
NNNIA0014ZZ
Revision: 2012 November
2014 GT-R
MWI-70
< REMOVAL AND INSTALLATION >
METER CONTROL SWITCH
4.
Remove the screws (A), and then remove the drive computer
switch (1), illumination control switch, and trip A/B reset switch
(2).
INSTALLATION
Install in the reverse order of removal.
NNNIA0015ZZ
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст