Qashqai J11. Interior lighting System — part 5
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
NO
>> Repair or replace harnesses.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and push-button ignition switch connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
BCM
Ground
Continuity
Connector
Terminal
M69
88
Not existed
INL-66
< SYMPTOM DIAGNOSIS >
INTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000010430921
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Room lamp
• Personal lamp
• Vanity mirror lamp
• Luggage room lamp
• Spicy illumination
• Fuse
• Harness between battery and interi-
or room lamp relay
• Harness between BCM and interior
room lamp relay
• Interior room lamp relay
• BCM
Interior room lamp power supply circuit
Refer to
.
Any of the following lamp does not turn ON.
• Map lamp
• Room lamp
• Personal lamp
• Vanity mirror lamp
• Harness between each interior room
lamp and interior room lamp relay
• Harness between each interior room
lamp and ground
• Each interior room lamp
Interior room lamp power supply circuit
Refer to
.
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• BCM
Door switch circuit
Refer to
(Type
(Type
(Type
(Type
4)*.
• Harness between BCM and each in-
terior room lamp
• BCM
Interior room lamp control circuit
Refer to
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/clos-
es.)
—
Check the interior room lamp setting.
Refer to
SULT Function (BCM - INT LAMP)"
.
• Luggage room lamp does not turn ON even
though the back door is open.
• Luggage room lamp does not turn OFF
even though the back door is closed.
• Harness between BCM and back
door switch
• BCM
Back door switch circuit
Refer to
(Type
(Type
(Type
(Type
4)*.
• Harness between luggage room
lamp and interior room lamp relay
• Harness between BCM and luggage
room lamp
• luggage room lamp
• BCM
Luggage room lamp circuit
Refer to
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-67
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
*: Refer to
for detailed vehicle information.
• Spicy illumination does not turn ON even
though the door is open.
• Spicy illumination does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• BCM
Door switch circuit
Refer to
(Type
(Type
(Type
(Type
4)*.
• Harness between spicy illumination
and interior room lamp relay
• Harness between BCM and spicy il-
lumination
• Spicy illumination
• BCM
Spicy illumination circuit
Refer to
Push-button ignition switch illumination does
not illuminate.
• Harness between BCM and push-
button ignition switch
• Harness between push-button igni-
tion switch and ground
• Push-button ignition switch
• BCM
Push-button ignition switch illumination
circuit
Refer to
Interior room lamp battery saver does not ac-
tivate.
• Harness between BCM and interior
room lamp relay
• Interior room lamp relay
• BCM
Interior room lamp power supply circuit
Refer to
Symptom
Possible cause
Inspection item
INL-68
< REMOVAL AND INSTALLATION >
MAP LAMP
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000010430922
With sunroof
MAP LAMP
MAP LAMP : Removal and Installation
INFOID:0000000010430923
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
JMLIA5183ZZ
Map lamp bracket
Headlining assembly
Map lamp finisher
Lamp housing
Bulb
Lens
: Pawl
: Metal clip
: Vehicle front
MAP LAMP
INL-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Disengage map lamp housing fixing pawl using a remover tool
(A), and then pull out lamp housing
according to numerical
order 1
→
2 indicated by arrows as shown in the figure.
CAUTION:
Apply protect tape on remover tool.
3.
Disconnect map lamp harness connector, and then remove map lamp housing.
INSTALLATION
Install in the reverse order of removal.
MAP LAMP : Replacement
INFOID:0000000010430924
MAP LAMP BULB
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Remove bulb.
MAP LAMP FINISHER
MAP LAMP FINISHER : Removal and Installation
INFOID:0000000010451298
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse while performing the operation
to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
REMOVAL
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
: Pawl
JMLIA1063ZZ
INL-70
< REMOVAL AND INSTALLATION >
MAP LAMP
1.
Disengage map lamp assembly fixing pawls and metal clips
according to numerical order 1
→
3 indicated by arrows as shown
in the figure.
2.
Disconnect harness connectors, and then remove map lamp assenbly.
3.
Remove the following parts after removing map lamp assembly.
• Map lamp: Refer to
INL-68, "MAP LAMP : Removal and Installation"
• Sunshade switch: Refer to
RF-35, "Removal and Installation"
. (With sunroof)
INSTALLATION
Install in the reverse order of removal.
MAP LAMP BRACKET
MAP LAMP BRACKET : Removal and Installation
INFOID:0000000010430925
REMOVAL
1.
Remove headlining assembly. Refer to
INT-25, "Removal and Installation"
2.
Remove map lamp bracket mounting bolts
, and then remove
map lamp bracket.
INSTALLATION
Install in the reverse order of removal.
: Pawl
: Metal clip
JMLIA5190ZZ
JMLIA5191ZZ
VANITY MIRROR LAMP
INL-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
VANITY MIRROR LAMP
Exploded View
INFOID:0000000010430926
Replacement
INFOID:0000000010430927
VANITY MIRROR LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Apply protective tape to vanity mirror of surface for protecting it from damage.
2.
Disengage lens fixing pawls using a remover tool, and then remove lens.
CAUTION:
Use a remover tool wrapped in tape.
3.
Remove bulb.
Lens
Bulb
Lens
: Pawl
JMLIA5184ZZ
INL-72
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded View
INFOID:0000000010430928
LHD models
Replacement
INFOID:0000000010430929
GLOVE BOX LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Remove instrument lower panel LH (RHD models) or RH (LHD models). Refer to
.
2.
Remove bulb & socket assembly according to numerical order
1
→
2 indicated by arrows as shown in the figure.
JMLIA5185ZZ
Lamp housing
Bulb & socket assembly
Instrument lower panel RH
: Pawl
: Vehicle front
JMLIA3624ZZ
SPICY ILLUMINATION
INL-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SPICY ILLUMINATION
Exploded View
INFOID:0000000010430930
REMOVAL
LHD models
DISASSEMBLY
JMLIA5186ZZ
Console panel assembly LH
Console panel assembly RH
: Pawl
: Metal clip
JMLIA5187ZZ
INL-74
< REMOVAL AND INSTALLATION >
SPICY ILLUMINATION
Replacement
INFOID:0000000010430932
SPICY ILLUMINATION BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Replacement of a single part is not possible due to the adoption of LED. For replacement, replace
spicy illumination assembly.
1.
Remove console panel assembly. Refer to
IP-19, "Removal and Installation"
.
2.
Remove console panel mask lid fixing screws
, and then
remove console panel mask lid.
3.
Remove harness connector fixing clip
, and then remove spicy
illumination assembly.
Console panel bracket RH
Console panel mask lid RH
Spicy illumination assembly
Console panel RH
: Clip
: Pawl
: Metal clip
: Vehicle front
JMLIA5192ZZ
JMLIA5193ZZ
ROOM LAMP
INL-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ROOM LAMP
Exploded View
INFOID:0000000010451272
Removal and Installation
INFOID:0000000010451273
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
REMOVAL
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
Lamp housing
Bulb
Lens
: Pawl
: Vehicle front
JMLIA2093ZZ
: Pawl
JMLIA1230ZZ
INL-76
< REMOVAL AND INSTALLATION >
ROOM LAMP
2.
Disengage lamp housing fixing pawl using a remover tool (A),
and then pull out lamp housing
according to numerical order
1
→
2 indicated by arrows as shown in the figure.
CAUTION:
Apply protect tape on remover tool.
3.
Disconnect harness connector, and then remove lamp housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010451274
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
ROOM LAMP BULB
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Remove bulb.
: Pawl
JMLIA1231ZZ
: Pawl
JMLIA1230ZZ
PERSONAL LAMP
INL-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PERSONAL LAMP
Exploded View
INFOID:0000000010430933
Removal and Installation
INFOID:0000000010430934
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
1.
Disengage personal lamp assembly fixing metal clips using a
remover tool (A).
2.
Disconnect harness connector, and then remove personal lamp assembly.
INSTALLATION
Personal lamp base
Bulb
Lens
: Pawl
: Metal clip
: Vehicle front
JMLIA5188ZZ
: Metal clip
JMLIA5194ZZ
INL-78
< REMOVAL AND INSTALLATION >
PERSONAL LAMP
Install in the reverse order of removal.
Replacement
INFOID:0000000010430935
PERSONAL LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Remove personal lamp assembly. Refer to
INL-77, "Removal and Installation"
2.
Disengage lens fixing pawls using a remover tool, and then
remove lens.
3.
Remove bulb.
: Pawl
JMLIA5195ZZ
LUGGAGE ROOM LAMP
INL-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
LUGGAGE ROOM LAMP
Exploded View
INFOID:0000000010430936
Removal and Installation
INFOID:0000000010430937
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
1.
Apply protective tape (A) to rear pillar finisher LH of surface for
protecting it from damage.
Shade
Bulb
Lens
: Pawl
: Vehicle front
JMLIA5189ZZ
JMLIA5196ZZ
INL-80
< REMOVAL AND INSTALLATION >
LUGGAGE ROOM LAMP
2.
Disengage luggage room lamp assembly fixing pawl using a
remover tool (A).
3.
Disconnect harness connector, and then remove luggage room lamp assembly.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010430938
LUGGAGE ROOM LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Remove luggage room lamp assembly. Refer to
INL-79, "Removal and Installation"
.
2.
Remove lens fixing pawls, and then remove lens.
3.
Remove bulb.
: Pawl
JMLIA5197ZZ
: Pawl
JMLIA5247ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
INL-81
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
bulb specifications
INFOID:0000000010430941
*1
: With Intelligent Key System
*2
: With vanity mirror lamp
*3
: With spicy illumination
*4
: Without sunshade system
*5
: With sunshade system
Item
Type
Wattage (W)
Push-button ignition switch illumination
*1
LED
—
Map lamp
Wedge
5.0
Vanity mirror lamp
*2
—
1.2
Glove box lamp
Wedge
1.4
Spicy illumination
*3
LED
—
Room lamp
*4
Wedge
5.0
Personal lamp
*5
—
8.0
Luggage room lamp
Wedge
5.0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст