Nissan Versa Note. Manual — part 248
REAR DOOR
DLK-277
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Loosen door hinge nuts (door side).
3. Adjust the surface height of rear door according to the specifications provided.
4. Temporarily tighten door hinge nuts (door side).
5. Loosen door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Apply touch-up paint (body color) to the head of hinge bolts and nuts.
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
8. Install center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal and
.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009645181
REMOVAL
Remove bolts and rear door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door striker bolts.
• Tighten door striker bolts to specification. Refer to
.
• After installation, check front door open/close operation. If necessary, adjust the door striker. Refer
DLK-277, "DOOR STRIKER : Adjustment"
.
DOOR STRIKER : Adjustment
INFOID:0000000009645182
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts.
2. Adjust door striker so that it becomes parallel with rear door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009645183
REMOVAL
1. Remove rear door assembly. Refer to
DLK-274, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal
3. Remove rear door hinge bolts and nuts (body side) and rear door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
PIIB2804J
DLK-278
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
• Apply anticorrosive agent to the door hinge mating surface.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After adjusting, apply touch-up paint (body color) to the head of door hinge bolts and nuts.
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009645184
REMOVAL
1. Remove rear door speaker. Refer to
AV-55, "Removal and Installation"
(BASE AUDIO),
(DISPLAY AUDIO) or
AV-243, "Removal and Installation"
(NAVIGATION).
2. Remove door check link bolt (body side).
3. Remove door check link bolts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close operation.
• Check door check link rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
JMKIA8072ZZ
JMKIA8074ZZ
BACK DOOR
DLK-279
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Exploded View
INFOID:0000000009645185
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009645188
CAUTION:
• Use two people when removing or installing the back door due to its heavy weight.
• Use shop cloths to protect surrounding components from damage during removal and installation of
back door.
REMOVAL
1. Remove back door inner finisher. Refer to
INT-36, "BACK DOOR INNER FINISHER : Removal and Instal-
.
2. Remove back door stay (LH/RH). Refer to
DLK-157, "BACK DOOR STAY : Removal and Installation"
.
1.
Back door hinge (RH)
2.
Back door hinge (LH)
3.
Back door stay (RH)
4.
Back door stay stud ball (RH)
5.
Back door stay (LH)
6.
Back door stay stud ball (LH)
7.
Bumper rubber seal
8.
Bumper rubber
9.
Spacer
10. Back door outer finisher
11. Back door assembly
AWKIA2571ZZ
DLK-280
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
3. Remove back door harness grommet (1), then pull harness from
the back door.
4. Disconnect washer tube from rear wiper.
5. Remove washer tube grommet (1), then pull washer tube from
the back door.
6. Support the back door assembly using a suitable tool.
WARNING:
Bodily injury may occur if back door assembly is not supported properly when removing the back
door spindle unit.
7. Remove back door hinge nuts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the surface between hinge and door side.
• When reusing stud ball, always apply locking sealant before installing stud ball to back door.
• After installation, perform the back door assembly adjustment procedure. Refer to
ALKIA3187ZZ
ALKIA3188ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст