Nissan Versa Note. Manual — part 679
SE-46
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
7.
Headrest holder (free)
8.
Seatback latch bracket (RH)
9.
Seatback latch (RH)
10. Seatback frame (RH)
11. Seatback latch finisher (RH)
12. Seatback latch release knob
13. Seatback trim (RH)
14. Seatback pad (RH)
15. Seat cushion hook
16. Seat cushion
17. Seat cushion pad
18. Seat cushion trim
19. Cup holder
20. Armrest
21. Armrest hinge bracket
22. Armrest pivot bolt bushing
23. Armrest pivot bolt
24. Armrest hinge bracket finisher
(RH)
25. Bushing
26. Armrest hinge bracket finisher (LH) 27. Seatback pad (LH)
28. Seatback trim (LH)
29. Seatback latch finisher (LH)
30. Seatback frame (LH)
31. Seatback latch bracket (LH)
32. Seatback latch (LH)
33. Seatbelt guide finisher
34. Seat belt guide
35. Seatback (LH)
Pawl
REAR SEAT
SE-47
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT WITHOUT ARMREST
AWJIA1137ZZ
1.
Seatback hinge trim
2.
Seatback hinge
3.
Seatback striker
4.
Headrest
5.
Seatback(RH)
6.
Headrest holder (locked)
7.
Headrest holder (free)
8.
Seatback latch bracket (RH)
9.
Seatback latch (RH)
10. Seatback frame (RH)
11. Seatback latch finisher (RH)
12. Seatback latch release knob
13. Seatback trim (RH)
14. Seatback pad (RH)
15. Seat cushion hook
16. Seat cushion
17. Seat cushion pad
18. Seat cushion trim
SE-48
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
Seat Cushion
INFOID:0000000009567502
DISASSEMBLY
1. Remove the seat cushion. Refer to
SE-30, "SEAT CUSHION : Removal and Installation"
.
2. Remove the hog rings on the bottom side of seat cushion.
3. Remove the hog rings on the top side of seat cushion and separate the seat cushion trim from the seat
cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
19. Seatback pad (LH)
20. Seatback trim (LH)
21. Seatback latch finisher (LH)
22. Seatback frame (LH)
23. Seatback latch bracket (LH)
24. Seatback latch (LH)
25. Seatbelt guide finisher
26. Seat belt guide
27. Seatback (LH)
Pawl
1.
Seat cushion pad
2.
Seat cushion trim
Hog rings
ALJIA1251ZZ
PIIB3356J
REAR SEAT
SE-49
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Seatback
INFOID:0000000009567504
DISASSEMBLY
Seatback (LH)
1. Remove the seatback (LH). Refer to
SE-30, "SEATBACK : Removal and Installation"
2. Remove the headrest.
3. Release clips and remove latch finisher.
4. Release pawls and remove the seat belt guide finisher.
5. Remove nut and the seat belt guide.
6. Rotate the seatback latch release knob counterclockwise as
shown (
) and remove.
7. Remove the armrest (1) (if equipped).
a. Remove clip (A) using a suitable tool, then the armrest bracket
finisher (RH) (2) as shown (
).
b. Remove nuts (B), then the armrest.
8. Release hook fasteners (A), then J-hook retainer (B).
9. Unzip the seatback trim zipper (C), then release J-clip retainers
(D).
10. Release the headrest holder locks as shown and remove.
CAUTION:
Before removing the headrest holder, check its orientation
(front/rear and right/left).
JMJIA4374ZZ
ALJIA1247ZZ
ALJIA1246ZZ
JMJIA4073ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст