Nissan Versa Note. Manual — part 216
REAR DOOR
DLK-149
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect the harness connector (A) from rear door.
3. Remove door check link bolt (body side).
4. Remove door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to the hinge mating surface.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After adjusting, apply touch-up paint (body color) to the head of door hinge nuts.
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
JMKIA8084ZZ
JMKIA8072ZZ
DLK-150
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009486671
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Remove center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Striker bolt
7.
Front door hinge
8.
Rear door upper hinge
9.
Rear door lower hinge
AWKIA2493ZZ
Section
Measurement
Standard
A – A
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
B – B
Clearance
4.6
± 2.0 (0.18 ± 0.08)
Surface height
0.0
± 1.5 (0.0 ± 0.06)
C – C
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
REAR DOOR
DLK-151
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Loosen door hinge nuts (door side).
3. Adjust the surface height of rear door according to the specifications provided.
4. Temporarily tighten door hinge nuts (door side).
5. Loosen door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Apply touch-up paint (body color) to the head of hinge bolts and nuts.
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
8. Install center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal and
.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009486672
REMOVAL
Remove bolts and rear door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door striker bolts.
• Tighten door striker bolts to specification. Refer to
.
• After installation, check front door open/close operation. If necessary, adjust the door striker. Refer
DLK-151, "DOOR STRIKER : Adjustment"
.
DOOR STRIKER : Adjustment
INFOID:0000000009541371
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts.
2. Adjust door striker so that it becomes parallel with rear door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009486673
REMOVAL
1. Remove rear door assembly. Refer to
DLK-148, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal
3. Remove rear door hinge bolts and nuts (body side) and rear door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
PIIB2804J
DLK-152
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
• Apply anticorrosive agent to the door hinge mating surface.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After adjusting, apply touch-up paint (body color) to the head of door hinge bolts and nuts.
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009486674
REMOVAL
1. Remove rear door speaker. Refer to
AV-55, "Removal and Installation"
(BASE AUDIO),
(DISPLAY AUDIO) or
AV-243, "Removal and Installation"
(NAVIGATION).
2. Remove door check link bolt (body side).
3. Remove door check link bolts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close operation.
• Check door check link rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
JMKIA8072ZZ
JMKIA8074ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст