Nissan Versa Note. Manual — part 782
TM-8
< PRECAUTION >
[5MT: RS5F91R]
PRECAUTIONS
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Liquid Gasket
INFOID:0000000009486775
REMOVAL OF LIQUID GASKET SEALING
• After removing the bolts and nuts, separate the mating surface and
remove the liquid gasket using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap (1) the cutter where the liquid gasket is applied. Use a
plastic hammer to slide (2) the cutter by tapping on the side.
CAUTION:
Do not damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using suitable tool (A), remove old liquid gasket adhering to the
liquid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to the suitable tool.
Use Genuine Silicone RTV Sealant, or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
4. Apply liquid gasket without gaps to the specified location accord-
ing to the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
• As for bolt holes (B), normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Check to read the text of this manual.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
Tool Number
: KV10111100 (J-37228)
AWBIA1249GB
JPBIA0053ZZ
EMA0622D
(A)
: Groove
: Inside
JPBIA0010ZZ
PRECAUTIONS
TM-9
< PRECAUTION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.
CAUTION:
If there are specific instructions in the procedures contained in this manual concerning liquid gas-
ket application, observe them.
TM-10
< PREPARATION >
[5MT: RS5F91R]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009417450
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV32500QAA
( — )
Drift set
Installing differential side oil seal
1.
—
Drift
a: 54.3 mm (2.138 in) dia.
b: 45 mm (1.77 in) dia.
c: 26.6 mm (1.047 in) dia.
2.
—
Drift
d: 54 mm (2.13 in) dia.
e: 48.6 mm (1.913 in) dia.
f: 26.6 mm (1.047 in) dia
KV32300QAC
( — )
Puller
Removing 5th main gear
KV32300QAD
( — )
Puller
Removing 5th main gear
ST35300000
( — )
Drift
• Removing and installing input shaft rear
bearing
• Removing and installing mainshaft rear
bearing
a: 45 mm (1.77 in) dia.
b: 59 mm (2.32 in) dia.
KV111011S0
( — )
Valve seat remover
Removing mainshaft front bearing
JPDIC0730ZZ
SCIA1781J
SCIA1782J
ZZA0969D
ZZA0872D
PREPARATION
TM-11
< PREPARATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ST33400001
( — )
Drift
Installing mainshaft front bearing
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
KV40100900
( — )
Drift
Installing input shaft front bearing
a: 52 mm (2.05 in) dia.
b: 39.5 mm (1.555 in) dia.
KV32300QAE
( — )
Drift
Installing differential side bearing outer race
a: 61.5 mm (2.421 in) dia.
ST33052000
( — )
Drift
Removing differential side bearing
a: 22 mm (0.87 in) dia.
b: 28mm (1.10 in) dia.
KV40104920
( — )
Drift
Installing differential side bearing
a: 21.7 mm (0.854 in) dia.
b: 44.7 mm (1.760 in) dia.
—
(J-46534)
Trim tool set
Removing trim components
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA0814D
NT084
JPDIC0635ZZ
ZZA0969D
ZZA0969D
AWJIA0483ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст