Nissan Versa Note. Manual — part 672
SE-18
< WIRING DIAGRAM >
HEATED SEAT SYSTEM
AAJIA0298GB
FRONT SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REMOVAL AND INSTALLATION
FRONT SEAT
DRIVER SIDE
DRIVER SIDE : Exploded View
INFOID:0000000009567477
DRIVER SEAT WITH LIFT
ALJIA1238ZZ
1.
Armrest
2.
Seatback trim
3.
Seatback pad
4.
Seat cushion trim
5.
Seat cushion pad
6.
Seat cushion frame
7.
Seat belt buckle
8.
Seat cushion outer finisher (RH)
9.
Seat cushion outer finisher (LH)
10. Lift lever
11. Lift lever finisher
12. Recline lever
13. Slide finisher rear (LH/RH)
14. Side air bag module
15. Chute rod
16. Headrest holder (locked)
17. Headrest holder (free)
18. Headrest
19. Seat frame
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
DRIVER SEAT WITHOUT LIFT
DRIVER SIDE : Removal and Installation
INFOID:0000000009567478
WARNING:
• Do not leave any objects (screwdrivers, tools, etc.) on the seat during repair. It can lead to personal
injury if the side air bag module should accidentally deploy.
• Always work from the side or back of the seatback, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After the side air bag module inflates, the front seat frame must be replaced.
ALJIA1237ZZ
1.
Seatback trim
2.
Seatback pad
3.
Seat cushion trim
4.
Seat cushion pad
5.
Seat cushion frame
6.
Seat belt buckle
7.
Seat cushion outer finisher (RH) 8.
Seat frame
9.
Seat cushion outer finisher (LH)
10. Recline lever
11. Slide finisher rear (LH/RH)
12. Side air bag module
13. Chute rod
14. Headrest holder (locked)
15. Headrest holder (free)
16. Headrest
FRONT SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
CAUTION:
• When removing and installing the seat, use shop cloths to protect components from damage.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Slide the seat to the full forward position.
3. Remove the seat rear bolts.
4. Slide the seat to the full rearward position.
5. Remove the seat front bolts.
6. Tilt the seat rearward and disconnect the harness connectors from the seat and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
When installing the driver side front seat, tighten the bolts in the
order shown.
PASSENGER SIDE
Driver side front seat bolt
torque
: 40 Nm (4.1 kg-m, 30 ft-lb)
AWJIA0920ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст