Nissan Versa Note. Manual — part 116
BRC-28
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
SYSTEM
DTC
Malfunction detected condition
Fail-safe condition
C1101
When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended:
• VDC
• ABS
• EBD (only when both rear wheels
are malfunctioning)
C1102
When an open circuit is detected in rear LH wheel sensor circuit.
C1103
When an open circuit is detected in front RH wheel sensor circuit.
C1104
When an open circuit is detected in front LH wheel sensor circuit.
C1105
• When a short circuit is detected in rear RH wheel sensor circuit.
• When power supply voltage of rear RH wheel sensor is in following state.
- Rear RH wheel sensor power supply voltage: 7.2 V
≥ Rear RH wheel sensor pow-
er supply voltage
• When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
• When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106
• When a short circuit is detected in rear LH wheel sensor circuit.
• When power supply voltage of rear LH wheel sensor is in following state.
- Rear LH wheel sensor power supply voltage: 7.2 V
≥ Rear LH wheel sensor power
supply voltage
• When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
• When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107
• When a short circuit is detected in front RH wheel sensor circuit.
• When power supply voltage of front RH wheel sensor is in following state.
- Front RH wheel sensor power supply voltage: 7.2 V
≥ Front RH wheel sensor
power supply voltage
• When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
• When installation of front RH wheel sensor or front RH wheel sensor rotor is not
normal.
C1108
• When a short circuit is detected in front LH wheel sensor circuit.
• When power supply voltage of front LH wheel sensor is in following state.
- Front LH wheel sensor power supply voltage: 7.2 V
≥ Front LH wheel sensor pow-
er supply voltage
• When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
• When installation of front LH wheel sensor or front LH wheel sensor rotor is not
normal.
C1109
• When ignition power supply voltage is in following state.
- Ignition power supply voltage: 10 V
≥ Ignition power supply voltage.
- Ignition power supply voltage: 16 V
≤ Ignition power supply voltage.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1110
When there is an internal malfunction in the ABS actuator and electric unit (control
unit).
C1111
When a malfunction is detected in motor or motor relay.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
C1115
When difference in wheel speed between any wheel and others is detected when
the vehicle is driven, because of installation of tires other than specified.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1116
When stop lamp switch signal is not input when brake pedal operates.
The following functions are sus-
pended:
• VDC
• TCS
SYSTEM
BRC-29
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1120
When a malfunction is detected in front LH ABS IN valve.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1121
When a malfunction is detected in front LH ABS OUT valve.
C1122
When a malfunction is detected in front RH ABS IN valve.
C1123
When a malfunction is detected in front RH ABS OUT valve.
C1124
When a malfunction is detected in rear LH ABS IN valve.
C1125
When a malfunction is detected in rear LH ABS OUT valve.
C1126
When a malfunction is detected in rear RH ABS IN valve.
C1127
When a malfunction is detected in rear RH ABS OUT valve.
C1130
When a malfunction is detected in ECM system.
The following functions are sus-
pended:
• VDC
• TCS
C1140
When a malfunction is detected in actuator relay.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1142
When a malfunction is detected in VDC pressure sensor.
The following functions are sus-
pended:
• VDC
• TCS
C1143
When a malfunction is detected in steering angle sensor.
C1144
When neutral position adjustment of steering angle sensor is not complete.
C1145
When a malfunction is detected in yaw rate signal, or signal line of yaw rate/side/
decel G sensor is open or shorted.
C1146
When a malfunction is detected in side G signal, or signal line of yaw rate/side/decel
G sensor is open or shorted.
C1153
When ABS actuator and electric unit (control unit) is malfunctioning. (Pressure in-
crease is too much or too little.)
The following functions are sus-
pended:
• VDC
• TCS
• ABS
C1155
When brake fluid level low signal is detected.
The following functions are sus-
pended:
• VDC
• TCS
C1164
When a malfunction is detected in cut valve 1.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1165
When a malfunction is detected in cut valve 2.
C1166
When a malfunction is detected in suction valve 1.
C1167
When a malfunction is detected in suction valve 2.
C1170
When the information in ABS actuator and electric unit (control unit) is not the same.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
U1000
When CAN communication signal is not continuously transmitted or received for 2
seconds or more.
The following functions are sus-
pended:
• VDC
• TCS
U1002
When ABS actuator and electric unit (control unit) is not transmitting or receiving
CAN communication signal for 2 seconds or less.
U1010
When detecting error during the initial diagnosis of CAN controller of ABS actuator
and electric unit (control unit)
DTC
Malfunction detected condition
Fail-safe condition
BRC-30
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT Function (ABS)
INFOID:0000000009364895
APPLICATION ITEMS
CONSULT can display each diagnostic item using the following direct diagnostic modes.
ECU IDENTIFICATION
ABS actuator and electric unit (control unit) part number is displayed.
SELF DIAGNOSTIC RESULT
Operation Procedure
1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How To Erase Self Diagnostic Result
1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately
1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp,
SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is normal, unless
the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid
level switch operation (when brake fluid is insufficient).
• VDC OFF switch should not stay in ON position.
Display Item List
.
DATA MONITOR
Direct Diagnostic Mode
Description
ECU identification
The ABS actuator and electric unit (control unit) part number is displayed.
Self Diagnostic Result
The ABS actuator and electric unit (control unit) self diagnostic results are displayed.
Data Monitor
The ABS actuator and electric unit (control unit) input/output data is displayed in real time.
Active Test
The ABS actuator and electric unit (control unit) activates outputs to test components.
Work support
The settings for ABS actuator and electric unit (control unit) functions can be changed.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication is displayed.
Item
(Unit)
Data monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
FR LH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by front wheel
sensor LH signal is displayed.
FR RH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by front wheel
sensor RH signal is displayed.
RR LH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by rear wheel
sensor LH signal is displayed.
RR RH SENSOR
(km/h, mph)
×
×
×
Wheel speed (km/h, mph) calculated by rear wheel
sensor RH signal is displayed.
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-31
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
FR RH IN SOL
(On/Off)
–
×
×
Front RH IN ABS solenoid (On/Off) status is dis-
played.
FR RH OUT SOL
(On/Off)
–
×
×
Front RH OUT ABS solenoid (On/Off) status is dis-
played.
FR LH IN SOL
(On/Off)
–
×
×
Front LH IN ABS solenoid (On/Off) status is displayed.
FR LH OUT SOL
(On/Off)
–
×
×
Front LH OUT ABS solenoid (On/Off) status is dis-
played.
RR RH IN SOL
(On/Off)
–
×
×
Rear RH IN ABS solenoid (On/Off) status is displayed.
RR RH OUT SOL
(On/Off)
–
×
×
Rear RH OUT ABS solenoid (On/Off) status is dis-
played.
RR LH IN SOL
(On/Off)
–
×
×
Rear LH IN ABS solenoid (On/Off) status is displayed.
RR LH OUT SOL
(On/Off)
–
×
×
Rear LH OUT ABS solenoid (On/Off) status is dis-
played.
EBD WARN LAMP
(On/Off)
–
–
×
Brake warning lamp (On/Off) status is displayed.
STOP LAMP SW
(On/Off)
×
×
×
Stop lamp switch (On/Off) status is displayed.
MOTOR RELAY
(On/Off)
–
×
×
ABS motor relay signal (On/Off) status is displayed.
ACTUATOR RLY
(On/Off)
–
×
×
ABS actuator relay signal (On/Off) status is displayed.
ABS WARN LAMP
(On/Off)
–
×
×
ABS warning lamp (On/Off) status is displayed.
OFF LAMP
(On/Off)
–
×
×
VDC OFF Lamp (On/Off) status is displayed.
OFF SW
×
×
×
VDC OFF Switch (On/Off) position is displayed
SLIP/VDC LAMP
(On/Off)
–
×
×
SLIP indicator lamp (On/Off) status is displayed.
BATTERY VOLT
(V)
×
×
×
Voltage (V) supplied to ABS actuator and electric unit
(control unit) is displayed.
GEAR
(1, 2, 3, 4, 5)
×
×
×
Gear position (1, 2, 3, 4, 5) judged by transmission
range switch signal is displayed.
SLCT LVR POSI
×
×
×
Current gear position judged from current gear posi-
tion signal is displayed.
ENGINE SPEED
×
×
×
Engine speed judged by CAN communication signal
is displayed.
YAW RATE SEN
(d/s)
×
×
×
Yaw rate (d/s) detected by yaw rate sensor is dis-
played.
R POSI SIG
(On/Off)
–
–
×
Reverse shift position (On/Off) judged by transmis-
sion range switch signal.
N POSI SIG
(On/Off)
–
–
×
Neutral position (On/Off) judged by transmission
range switch signal.
P POSI SIG
(On/Off)
–
–
×
Park position (On/Off) judged by transmission range
switch signal.
CV1
(On/Off)
–
–
×
Cut valve 1(On/Off) status is displayed.
CV2
(On/Off)
–
–
×
Cut valve 2 (On/Off) status is displayed.
Item
(Unit)
Data monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст