Nissan Versa Note. Manual — part 594
MWI
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
MWI-51
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000009654135
• The door ajar warning is displayed even though all of the doors are closed.
• The door ajar warning is not displayed even though a door is ajar.
Diagnosis Procedure
INFOID:0000000009654136
1.
CHECK BCM INPUT SIGNAL
Check the BCM input signal. Refer to
DLK-95, "Component Function Check"
(with Intelligent Key) or
225, "Component Function Check"
(without Intelligent Key).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the METER/M&A Data Monitor and check the DOOR W/L monitor value while opening and closing
doors.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
3.
CHECK DOOR SWITCH SIGNAL CIRCUIT
Check the door switch signal circuit. Refer to
(with Intelligent Key) or
(without Intelligent Key).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK DOOR SWITCH
Check the door switch. Refer to
DLK-96, "Component Inspection"
(with Intelligent Key) or
(without Intelligent Key).
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Replace applicable door switch. Refer to
DLK-175, "Removal and Installation"
(with Intelligent
DLK-301, "Removal and Installation"
Monitor item
Condition
Status
DOOR W/L
Door open
ON
Door closed
OFF
MWI-52
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
Description
INFOID:0000000009654137
• The parking brake warning is displayed while driving the vehicle even though the parking brake is released.
• The parking brake warning is not displayed while driving the vehicle even though the parking brake is
applied.
Diagnosis Procedure
INFOID:0000000009654138
1.
CHECK PARKING BRAKE WARNING LAMP OPERATION
1. Start engine.
2. Check the operation of the brake warning lamp while operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to
WCS-39, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace parking brake switch. Refer to
PB-9, "Removal and Installation"
3.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Check the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Condition
Warning lamp status
Parking brake applied
ON
Parking brake released
OFF
MWI
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
MWI-53
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000009682044
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000009682045
1.
CHECK WASHER FLUID LEVEL SWITCH
Check the washer fluid level switch. Refer to
MWI-47, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace washer fluid level switch. Refer to
WW-64, "Removal and Installation"
.
2.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Repair or replace harness or connector.
MWI-54
< UNIT REMOVAL AND INSTALLATION >
COMBINATION METER
UNIT REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000009477606
REMOVAL
1. Disconnect negative battery terminal. Refer to
PG-67, "Removal and Installation (Battery)"
.
2. Remove cluster lid A. Refer to
IP-21, "Removal and Installation"
3. Remove combination meter screws (A).
4. Pull the combination meter straight out to release clips.
NOTE:
Back side of the combination meter shown for clip position (
)
clarity.
5. Disconnect the harness connector from the combination meter.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1519ZZ
JSNIA3895ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст