Nissan Versa Note. Manual — part 888
FRONT WIPER DRIVE ASSEMBLY
WW-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000009596022
Removal and Installation
INFOID:0000000009578787
REMOVAL
1. Remove cowl top cover. Refer to
EXT-35, "Removal and Installation"
.
2. Disconnect the harness connector from front wiper motor.
3. Remove bolts and front wiper drive assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Tighten front wiper drive assembly bolts to specification. Refer to
.
1.
Wiper arm cap (LH/RH)
2.
Wiper arm (LH)
3.
Wiper blade (LH)
4.
Wiper arm (RH)
5.
Wiper blade (RH)
6.
Front wiper drive assembly
ALLIA1310ZZ
WW-72
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000009596023
Disassembly and Assembly
INFOID:0000000009578788
DISASSEMBLY
1. Remove front wiper drive assembly. Refer to
WW-71, "Removal and Installation"
2. Remove wiper linkage 1 and 2 from the front wiper drive.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
3. Remove screws and wiper motor from front wiper drive.
ASSEMBLY
1. Install wiper motor screws and wiper motor to front wiper drive.
2. Install wiper linkage 2 to the front wiper drive.
CAUTION:
• Do not drop wiper motor or cause it to come into contact with other parts.
• Be careful of the grease condition at the wiper motor and wiper linkage joint (retainer). Apply a
suitable multi
−purpose grease if necessary.
3. Install wiper linkage 1 to the wiper motor and the front wiper drive.
4. Install front wiper drive assembly. Refer to
WW-71, "Removal and Installation"
1.
Wiper linkage 2
2.
Wiper linkage 1
3.
Front wiper motor
4.
Front wiper drive
ALLIA1311ZZ
WIPER AND WASHER SWITCH
WW-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER AND WASHER SWITCH
Removal and Installation
INFOID:0000000009578798
The wiper and washer switch is part of the combination switch. Refer to
WW-74
< REMOVAL AND INSTALLATION >
REAR WIPER ARM
REAR WIPER ARM
Exploded View
INFOID:0000000009578892
Removal and Installation
INFOID:0000000009578893
REMOVAL
1. Operate the rear wiper to move it to the auto stop position.
2. Remove rear wiper arm cover.
3. Remove nut and rear wiper arm.
INSTALLATION
1. Clean the rear wiper arm as shown. This will reduce the possibil-
ity of wiper arm looseness.
2. Adjust the rear wiper blade position. Refer to
3. Install the rear wiper arm and nut.
4. Install the rear wiper arm cover.
5. Check that the rear wiper blade stops at the specified position. Refer to
1.
Rear wiper motor
2.
Rear wiper arm seal
3.
Rear wiper arm cover
4.
Rear wiper arm
5.
Rear wiper blade
ALLIA1312ZZ
SKIA0082J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст