Nissan Versa Note. Manual — part 793
TM-52
< UNIT DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
FINAL DRIVE
FINAL DRIVE
Exploded View
INFOID:0000000009417486
Disassembly
INFOID:0000000009417487
• Remove differential side bearings, using Tool (A) and suitable tool.
Assembly
INFOID:0000000009417488
• Install differential side bearings, using Tool (A).
CAUTION:
Replace differential side bearing outer race and differential
side bearing as a set.
Inspection
INFOID:0000000009417489
INSPECTION AFTER DISASSEMBLY
Gear and Final Drive
1.
Differential side bearing outer race
2.
Differential side bearing
3.
Final drive
: Replace the parts as a set.
JPDIC0481ZZ
Tool number
: ST33052000 ( — )
PCIB1568E
Tool number
: KV40104920 ( — )
PCIB1570E
FINAL DRIVE
TM-53
< UNIT DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check the sliding surfaces for wear, crack, or damage. Replace if necessary.
Bearing
Check bearing for damage and rough rotation. Replace if necessary.
SPD715
TM-54
< SERVICE DATA AND SPECIFICATIONS (SDS)
[5MT: RS5F91R]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000009417490
Transaxle type
RS5F91R
Engine type
HR16DE
Model code number
3AM0C
Number of speed
5
Synchromesh type
Warner
Shift pattern
Gear ratio
1st
3.7273
2nd
2.0476
3rd
1.3929
4th
1.0294
5th
0.8205
Reverse
3.5455
Final gear
4.0667
Number of
teeth
Input gear
1st
11
2nd
21
3rd
28
4th
34
5th
39
Reverse
11
Main gear
1st
41
2nd
43
3rd
39
4th
35
5th
32
Reverse
39
Reverse idler gear
26
Final gear
Final gear/Pinion
61/15
Side gear/Pinion mate gear
13/9
Gear oil capacity (Reference)
(US pt, Imp pt)
Approx. 2.67 (5-5/8, 4-3/4)
Remarks
Reverse brake
Installed
Double-cone synchronizer
1st and 2nd
Speedometer drive gear
Not installed
SCIA0821E
PRECAUTIONS
TM-55
< PRECAUTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009578754
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009019576
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for TCM and Transaxle Assembly Replacement
INFOID:0000000009019577
CAUTION:
• To replace TCM, refer to
• To replace transaxle assembly, refer to
Precaution for G Sensor Removal/Installation or Replacement
INFOID:0000000009019578
CAUTION:
To remove/install or replace G sensor, refer to
PIIB3706J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст