Nissan Versa Note. Manual — part 481
GW-22
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
7. Remove front door glass bolts (A).
8. While holding the front door glass, raise it at the rear end and
pull it out of the front door glass rear run toward the outside of
the door to remove.
9. Remove the front door glass front run bolts and remove (if necessary).
10. Remove the front door glass rear run bolts and remove (if necessary).
Installation
Installation is in the reverse order of removal.
CAUTION:
Tighten bolts to specification. Refer to
Fitting Inspection
• Make sure that the glass fits securely into the front door glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator bolts, door sash bolts and glass bolts to correct the glass position if the
clearance between the glass and sash is not parallel.
FRONT DOOR GLASS REGULATOR
Removal
1. Disconnect the battery positive and negative terminals then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove the vapor barrier. Refer to
CAUTION:
Use care not to damage or tear vapor barrier during removal.
4. Disconnect the harness connector from the door mirror.
5. Temporarily reconnect both battery terminals and the main power window and door lock/unlock switch (LH
door) or power window and door lock/unlock switch (RH door) to raise/lower the front door glass until the
bolts can be seen through the access holes (with power window).
6. Temporarily reinstall the front door glass handle and raise/lower the front door glass until the bolts can be
seen through the access holes (without power window).
ALKIA3164ZZ
JMKIA8064ZZ
FRONT DOOR GLASS AND REGULATOR
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
7. Remove front door glass bolts (A).
8. Raise the front door glass and hold it in place with a suitable tool or approximately two inches of mashing
tape.
9. Remove bolts and front door glass regulator.
10. Remove front power window motor from front door glass regulator (if necessary). Refer to
Inspection After Removal
Check the front door glass regulator for the following items:
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
If a malfunction is detected, replace or grease it.
The arrows in the figure show the application points of a suitable
multi-purpose grease (if necessary).
Installation
Installation is in the reverse order of removal.
CAUTION:
Tighten front door regulator bolts to specification. Refer to
.
Fitting Inspection
• Make sure that the glass fits securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator bolts, door sash bolts and glass bolts to correct the glass position if the
clearance between the glass and sash is not parallel.
ALKIA3164ZZ
JMKIA4453ZZ
GW-24
< REMOVAL AND INSTALLATION >
FRONT POWER WINDOW MOTOR
FRONT POWER WINDOW MOTOR
Removal and Installation
INFOID:0000000009654177
REMOVAL
1. Remove front door glass regulator. Refer to
GW-21, "Removal and Installation"
.
2. Remove bolts and front power window motor.
INSTALLATION
Installation is in the reverse order of removal.
REAR DOOR GLASS AND REGULATOR
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS AND REGULATOR
Exploded View
INFOID:0000000008969488
Removal and Installation
INFOID:0000000009429683
REAR DOOR GLASS
Removal
1. Remove rear door finisher. Refer to
INT-18, "Removal and Installation"
.
2. Remove vapor barrier. Refer to
CAUTION:
Use care not to damage or tear vapor barrier during removal.
3. Temporarily reconnect the rear power window switch to raise/lower the rear door glass until the bolts can
be seen through the access holes (with power window).
4. Temporarily reinstall the rear door glass handle and raise/lower the rear door glass until the bolts can be
seen through the access holes (without power window).
1.
Rear door panel
2.
Vapor barrier
3.
Rear door glass front run
4.
Rear door glass
5.
Rear door glass rear run
6.
Rear door glass rubber run
7.
Rear door corner finisher
8.
Rear door glass regulator
9.
Rear power window motor
10. Rear door glass handle grommet
11. Rear door glass handle
A.
With power window
B.
Without power window
Clip
AWKIA2562ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст