Nissan Versa Note. Manual — part 50
AV-192
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
3. Check continuity between around view monitor control unit connector B54 and RH side camera connector
D107.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK RH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector B54.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
NO
>> Replace RH side camera. Refer to
AV-251, "Removal and Installation"
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
B54
36
D107
8
Yes
35
7
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
36
No
Around view monitor control unit connector B54
Condition
Reference value
(+)
(
−)
Terminal
Terminal
36
35
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
AV-193
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000009694242
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009694243
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and front camera connectors.
3. Check continuity between around view monitor control unit connector B54 and front camera connector
E71.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK FRONT CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and front camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
3.
CHECK FRONT CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and front camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Front display output signal diag-
nosis (Harness disconnection)
[U111C]
Front camera image signal circuit open or short.
Check front camera image signal circuit.
Around view monitor control unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
B54
38
E71
1
Yes
37
2
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
38
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
B54
38
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
AV-194
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
3. Check continuity between around view monitor control unit connector B54 and front camera connector
E71.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK FRONT CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and front camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector B54.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
NO
>> Replace front camera. Refer to
AV-249, "Removal and Installation"
.
Around view monitor control unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
B54
40
E71
3
Yes
39
4
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
40
No
Around view monitor control unit connector B54
Condition
Reference value
(+)
(
−)
Terminal
Terminal
40
39
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
AV-195
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000009694244
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009694245
Regarding Wiring Diagram information, refer to
.
1.
CHECK LH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector B54 and LH side camera connector
D4.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
3.
CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Left side display output signal
diagnosis (Harness disconnec-
tion)
[U111D]
Left side camera image signal circuit open or
short.
Check left side camera image signal circuit.
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
B54
30
D4
2
Yes
29
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
30
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
B54
30
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст