Nissan Versa Note. Manual — part 659
REAR WHEEL HUB
RAX-7
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
If required, position the wheel stud (1) to the brake drum. Place
Position the stud (1) to the brake drum. Place a washer (A) on the
opposite end of the stud and by use of a nut (B), tighten to press the
stud into the brake drum.
CAUTION:
• Check that no clearance exists between brake drum, and the
wheel stud after installation.
• Do not reuse wheel stud.
Insert brake drum in a straight line onto the spindle.
CAUTION:
• If the brake drum becomes stuck and must be pulled out, do not use tools. Replace the wheel bear-
ing with a new one if the brake drum cannot be pulled out without use of tools.
• If the brake drum becomes stuck and the wheel bearing inner race is damaged, replace the wheel
bearing with a new one.
• Do not damage the wheel bearing seal. If damaged, replace wheel bearing with new one.
Using the Tool, install hub cap on brake drum as shown.
CAUTION:
• Do not reuse hub cap.
• Do not reuse wheel hub lock nut.
• Tighten the wheel hub lock nut to the specified torque. Refer
.
Disassembly and Assembly
INFOID:0000000009486652
DISASSEMBLY
1. Remove sensor rotor, using a suitable tool (A).
CAUTION:
Do not damage the brake drum.
2. Remove snap ring (1).
Wheel stud press-fit load
: Refer to
JPDIF0300ZZ
Tool number : ST30720000 ( — )
SDIA0766J
JPDIG0097ZZ
JPDIG0092ZZ
RAX-8
< REMOVAL AND INSTALLATION >
REAR WHEEL HUB
3. Remove wheel bearing, using the Tool.
ASSEMBLY
1. Install wheel bearing (1) to brake drum (2), using the Tool (A).
CAUTION:
• Do not reuse wheel bearing.
• Do not apply lubricating oil to the press-fit surface of the
wheel hub bearing.
• Install wheel bearing with the seal rubber part (B) faced to
the brake drum side.
• Set brake drum and wheel bearing horizontally and insert
them vertically.
• The press-fit load must be applied to the wheel bearing
outer race and the brake drum.
• Do not apply press-fit load to the wheel bearing inner race, the seal (B) on the rubber surface
side, and the seal (C) on the metallic surface side. If a press-fit load is applied, the wheel bearing
must be replaced with a new one.
2. Install snap ring to brake drum.
CAUTION:
• Do not damage the wheel bearing seal.
• The snap ring must be installed evenly into the groove.
3. Install sensor rotor, using the Tool (A).
CAUTION:
Do not reuse sensor rotor.
Inspection
INFOID:0000000009486653
INSPECTION AFTER REMOVAL
Check the brake drum and spindle for wear, cracks, and damage. Replace if necessary.
INSPECTION AFTER DISASSEMBLY
• Check brake drum for wear, cracks, or any other damage. Replace if necessary.
• Check snap ring for wear or cracks. Replace if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel bearing rotating torque per the following instructions.
Tool number : ST33710000 ( — )
JPDIG0079ZZ
Tool number : KV40104730 ( — )
Wheel bearing
press-fit load
: Refer to
Tool number : ST30032000 ( — )
JPDIG0200ZZ
JPDIG0191ZZ
REAR WHEEL HUB
RAX-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOTE:
The adequacy of turning torque can be judged from a measurement value by a suitable tool.
a. Check the contact surface of the brake drum and spindle for foreign matter. If there is any foreign matter,
clean the contact surface.
b. Check that the wheel hub lock nut is tightened to the specified torque.
c. Turn the brake drum 10 times or more both clockwise and counterclockwise for proper fit.
d. Set a suitable tool to the wheel nut and measure turning torque
at turning speeds of 8 to 12 rpm.
2. Adjust parking brake operation (stroke). Refer to
.
Wheel bearing rotat-
ing torque
: Refer to
.
MDIA0060E
RAX-10
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000008969752
Wheel Hub
INFOID:0000000009499765
Item
Standard
Axial end play
0.0 mm (0.00 in) or less
Rotating torque
1.71 N·m (0.17 kg-m, 15 in-lb) or less
Spring balance measurement
34.2 N (3.49 kg, 7.69 lb) or less
Wheel bearing press-fit load
44.1 - 53.9 kN (4,498.2 - 5,497.8 kg-f, 9,913.7 - 12,116.7 lb-f)
Item
Standard
Wheel stud press-fit load
26.5 - 32.3 kN (2,703.0 - 3,294.6 kg-f, 5,957.2 - 7,261.0 lb-f)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст