Nissan Versa Note. Manual — part 235
DOOR SWITCH
DLK-225
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Description
INFOID:0000000009645371
Detects door open/close condition.
Component Function Check
INFOID:0000000009645372
1.
CHECK FUNCTION
With CONSULT
Check door switches DOOR SW-DR, DOOR SW-AS, DOOR SW-RL, DOOR SW-RR in Data Monitor mode
with CONSULT.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-225, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009645373
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscilloscope.
Monitor item
Condition
DOOR SW-DR
CLOSE
→ OPEN: OFF → ON
DOOR SW-AS
DOOR SW-RL
DOOR SW-RR
DLK-226
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 2
2.
CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and door switch connector.
Terminals
Door condition
Voltage (V)
(Approx.)
(+)
(–)
BCM
connector
Terminal
M20
60
Ground
Front RH
OPEN
0
CLOSE
57
Rear RH
OPEN
0
CLOSE
59
Front LH
OPEN
0
CLOSE
58
Rear LH
OPEN
0
CLOSE
JPMIA0011GB
JPMIA0011GB
JPMIA0011GB
JPMIA0011GB
BCM connector
Terminal
Door switch
connector
Terminal
Continuity
M20
60
B16 (Front RH)
3
Yes
57
B17 (Rear RH)
59
B8 (Front LH)
58
B6 (Rear LH)
DOOR SWITCH
DLK-227
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness between BCM and door switch.
3.
CHECK DOOR SWITCH
DLK-227, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace malfunctioning door switch.
4.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000009645374
1.
CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect door switch connector.
3. Check door switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace malfunctioning door switch.
BCM connector
Terminal
Ground
Continuity
M20
60
No
57
59
58
Terminal
Door switch condition
Continuity
Door switch
3
Ground part of
door switch
Pressed
No
Released
Yes
DLK-228
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009645375
Transmits door lock/unlock operation to BCM.
DRIVER SIDE : Component Function Check
INFOID:0000000009645376
1.
CHECK FUNCTION
With CONSULT
Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-228, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009645377
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage at the main power window and door lock/unlock switch connector when the switch (driver
side) is turned to “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> GO TO 2
2.
CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch connector.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
Monitor item
Condition
CDL LOCK SW
LOCK
: ON
UNLOCK
: OFF
CDL UNLOCK SW
LOCK
: OFF
UNLOCK
: ON
Connector
Main power window and
door lock/unlock switch
state
Terminal
Voltage
D7
Neutral
→ Unlock
6
Ground Battery voltage
→ 0
D8
Neutral
→ Lock
18
Main power window and door
lock/unlock switch connector
Terminal
Continuity
D8
17
Ground
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст