Nissan Versa Note. Manual — part 506
FRONT BLOWER MOTOR RESISTOR
HAC-59
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
FRONT BLOWER MOTOR RESISTOR
Exploded View
INFOID:0000000009395321
Removal and Installation
INFOID:0000000009395322
REMOVAL
1. Disconnect harness connector from front blower motor resistor.
2. Remove screws and front blower motor resistor.
INSTALLATION
Installation is in the reverse order of removal.
1. Heating and cooling unit assembly
2. Front blower motor
3. Front blower motor resistor
AWIIA1465ZZ
HAC-60
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
DOOR CABLE
DOOR CABLE
Exploded View
INFOID:0000000008968977
INTAKE DOOR CABLE
INTAKE DOOR CABLE : Removal and Installation
INFOID:0000000009395323
The intake door cable is not serviced separately. Refer to
HAC-56, "Removal and Installation"
.
INTAKE DOOR CABLE : Adjustment
INFOID:0000000009395324
1. Remove glove box assembly. Refer to
IP-25, "Removal and Installation"
2. Disconnect intake door cable (1) from clip (A).
3. Set intake door lever to REC position.
4. Push intake door link (2) in the direction shown, then carefully
pull outer cable to front air control side and connect clip.
1.
Heating and cooling unit assembly
2.
Plate
3.
Air mix door linkage 2
4.
Air mix door linkage 1
5.
Air mix door cable
6.
Intake door lever
7.
Intake door linkage
8.
Intake door cable
9.
Foot door lever
10. Mode door cable
11. Main linkage
12. Ventilator door rod
13. Ventilator door lever
A.
To front air control
JMIIA1742ZZ
JMIIA0617ZZ
DOOR CABLE
HAC-61
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
5. Operate intake door lever to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
MODE DOOR CABLE
MODE DOOR CABLE : Removal and Installation
INFOID:0000000009395325
The mode door cable is not serviced separately. Refer to
HAC-56, "Removal and Installation"
.
MODE DOOR CABLE : Adjustment
INFOID:0000000009395326
1. Remove glove box assembly. Refer to
IP-25, "Removal and Installation"
2. Disconnect mode door cable (1) from clip (A).
3. Set mode dial to VENT position.
4. Push main link (2) in the direction shown, then carefully pull
outer cable to front air control side and connect clip.
5. Operate mode dial to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
AIR MIX DOOR CABLE
AIR MIX DOOR CABLE : Removal and Installation
INFOID:0000000009395327
The air mix door cable is not serviced separately. Refer to
HAC-56, "Removal and Installation"
AIR MIX DOOR CABLE : Adjustment
INFOID:0000000009395328
1. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
2. Remove foot duct (LH). Refer to
VTL-7, "FOOT DUCT : Removal and Installation"
3. Disconnect air mix door cable (1) from clip (A).
4. Set temperature dial to full cold position.
5. Push air mix door link (2) in the direction shown, then carefully
pull outer cable to front air control side and connect clip.
6. Operate temperature dial to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
JMIIA0618ZZ
JMIIA0619ZZ
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст