Nissan Versa Note. Manual — part 198
COMBINATION METER BUZZER
DLK-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000009645304
1.
CHECK FUNCTION
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select INSIDE BUZZER in ACTIVE TEST mode.
3. Touch Key, Knob or Take Out to check that it works normally.
Is the inspection result normal?
Yes
>> Combination meter buzzer is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009645305
1.
CHECK METER BUZZER CIRCUIT
WCS-35, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
DLK-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000009645306
1.
CHECK FUNCTION
1. Select DOOR LOCK of BCM using CONSULT.
2. Select DOOR LOCK in ACTIVE TEST mode.
3. Touch ALL LOCK or ALL UNLK to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-78, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009645307
Regarding Wiring Diagram information, refer to
DLK-51, "POWER DOOR LOCK SYSTEM : Wiring Diagram"
.
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock actuator LH connector.
3. Check voltage between front door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock actuator LH .
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connector and front door lock actuator LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock actuator
LH
Connector
Terminal
D14
1
Ground
Door lock and unlock switch
Lock
Battery voltage
2
Unlock
BCM
Front door lock actuator LH
Continuity
Connector
Terminal
Connector
Terminal
M99
65
D14
1
Yes
66
2
BCM
Ground
Continuity
Connector
Terminal
M99
65
No
66
DOOR LOCK ACTUATOR
DLK-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Connect BCM connector.
2. Check voltage between front door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000009645308
1.
CHECK FUNCTION
1. Select DOOR LOCK of BCM using CONSULT.
2. Select DOOR LOCK in ACTIVE TEST mode.
3. Touch ALL LOCK or ALL UNLK to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-79, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009645309
Regarding Wiring Diagram information, refer to
DLK-51, "POWER DOOR LOCK SYSTEM : Wiring Diagram"
.
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock actuator RH connector.
3. Check voltage between front door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock actuator (RH).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuators.
2. Check continuity between BCM harness connector and front door lock actuator RH harness connector.
3. Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M99
65
Ground
Door lock and unlock switch
Lock
Battery voltage
66
Unlock
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock actuator
RH
Connector
Terminal
D114
2
Ground
Door lock and unlock switch
Lock
Battery voltage
1
Unlock
BCM
Front door lock actuator RH
Continuity
Connector
Terminal
Connector
Terminal
M99
65
D114
2
Yes
59
1
DLK-80
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between front door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
REAR LH
REAR LH : Component Function Check
INFOID:0000000009645310
1.
CHECK FUNCTION
1. Select DOOR LOCK of BCM using CONSULT.
2. Select DOOR LOCK in ACTIVE TEST mode.
3. Touch ALL LOCK or ALL UNLK to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-81, "REAR RH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000009645311
Regarding Wiring Diagram information, refer to
DLK-51, "POWER DOOR LOCK SYSTEM : Wiring Diagram"
.
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock actuator LH connector.
3. Check voltage between rear door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator LH. Refer to
.
NO
>> GO TO 2.
BCM
Ground
Continuity
Connector
Terminal
M99
65
No
59
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M99
65
Ground
Door lock and unlock switch
Lock
Battery voltage
59
Unlock
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock actuator LH
Connector
Terminal
D205
1
Ground
Door lock and unlock switch
Lock
Battery voltage
2
Unlock
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст