Nissan Versa Note. Manual — part 685
SYSTEM
SEC-19
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
switches to the ARMED phase when vehicle conditions are not changed for 30 seconds. Security indicator
lamp illuminates while being in this phase.
To reset the PRE-ARMED phase, refer to the switching condition of No. 10 in the table above.
ARMED Phase
The vehicle security system is set and BCM monitors all necessary inputs. If any door is opened without using
Intelligent Key, vehicle security system switches to the ALARM phase. Security indicator lamp blinks every 2.4
seconds.
To reset the ARMED phase, refer to the switching condition of No. 11 in the table above.
ALARM Phase
BCM transmits “Theft Warning Horn Request” signal and “High Beam Request” signal intermittently to IPDM
E/R via CAN communication. In this phase, horns and headlamps are activated intermittently for approxi-
mately 50 seconds to warn that the vehicle is accessed by unauthorized means. ON/OFF timing of horns and
headlamps are synchronized. After 50 seconds, the vehicle security system returns to the ARMED phase. At
this time, if BCM still detects unauthorized access to the vehicle, the system is switched to the ALARM phase
again. This RE-ALARM operation is carried out a maximum of 2 times.
To cancel the ALARM operation, refer to the switching condition of No. 12 in the table above.
NOTE:
If a battery terminal is disconnected during the ALARM phase, theft warning alarm stops. But when the battery
terminal is reconnected, theft warning alarm is activated again.
PANIC ALARM
• The panic alarm function activates horns and headlamps intermittently when the owner presses the PANIC
ALARM button of Intelligent Key outside the vehicle while the power supply position is OFF or LOCK.
• When BCM receives panic alarm signal from Intelligent Key, BCM transmits “Theft Warning Horn Request”
signal and “High Beam Request” signal intermittently to IPDM E/R via CAN communication. To prevent the
activation due to mis-operation of Intelligent Key by owner, the panic alarm function is activated when BCM
receives the signal for 0.4 - 0.6 seconds.
• Panic alarm operation is maintained for 25 seconds.
• Panic alarm operation is cancelled when BCM receives one of the following signals:
- LOCK button of Intelligent Key: ON
- UNLOCK button of Intelligent Key: ON
- PANIC ALARM button of Intelligent Key: Long pressed
- Any door request switch: ON
SEC-20
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000009697556
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
ECU identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
ECU id
en
tif
ica
tion
Se
lf Di
ag
no
st
ic
Res
u
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
o
rk
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN DIAG SUP
P
OR
T MNTR
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
Air conditioner
AIR CONDITIONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Panic alarm system
PANIC ALARM
×
DIAGNOSIS SYSTEM (BCM)
SEC-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000009697557
SELF DIAGNOSTIC RESULT
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit]
Main
Description
REQ SW -DR [On/Off]
×
Indicates condition of door request switch LH.
REQ SW -AS [On/Off]
×
Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off]
×
Indicates condition of back door request switch.
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
CLUTCH SW [On/Off]
×
Indicates condition of clutch interlock switch.
BRAKE SW 1 [On/Off]
×
Indicates condition of brake switch.
BRAKE SW 2 [On/Off]
Indicates condition of brake switch.
DETE/CANCL SW [On/Off]
×
Indicates condition of P (park) position.
SFT PN/N SW [On/Off]
×
Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off]
×
Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off]
Indicates condition of push-button ignition switch received from IPDM E/R on
CAN communication line.
IGN RLY1 -F/B [On/Off]
Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.
DETE SW -IPDM [On/Off]
Indicates condition of detent switch received from TCM on CAN communication
line.
SFT PN -IPDM [On/Off]
Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.
SFT P -MET [On/Off]
Indicates condition of P (park) position from TCM on CAN communication line.
SFT N -MET [On/Off]
Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.
ENGINE STATE [Stop/Start/Crank/Run]
×
Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h]
×
Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line.
VEH SPEED 2 [mph/km/h]
×
Indicates condition of vehicle speed signal received from combination meter on
CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK]
×
Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK]
×
Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset]
Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset]
Indicates condition of engine start possibility.
RKE OPE COUN1 [0-19]
×
When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19]
×
When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key.
RKE-PANIC [On/Off]
Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off]
Indicates condition of mode change signal from Intelligent Key.
SEC-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
Test Item
Description
INSIDE BUZZER
This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
LCD
This test is able to check combination meter display information [Off/LK WN/OUTKEY/NO
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].
BATTERY SAVER
This test is able to check battery saver operation [On/Off].
ENGINE SW ILLUMI
This test is able to check push-button ignition switch START indicator operation [On/Off].
PUSH SWITCH INDICATOR
This test is able to check push-button ignition switch indicator operation [On/Off].
INT LAMP
This test is able to check interior room lamp operation [On/Off].
INDICATOR
This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
FLASHER
This test is able to check hazard lamp operation [LH/RH/Off].
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation [On/Off].
HORN
This test is able to check horn operation [On].
P RANGE
This test is able to check CVT shift selector illumination operation [On/Off].
Support Item
Setting
Description
LOCK/UNLOCK BY I-KEY
On*
Door lock/unlock function from Intelligent Key ON.
Off
Door lock/unlock function from Intelligent Key OFF.
ANTI KEY LOCK IN FUNCTI
On*
Anti lock out setting ON.
Off
Anti lock out setting OFF.
ANS BACK I-KEY UNLOCK
Off
No buzzer reminder when doors are unlocked with request switch.
On*
Buzzer reminder when doors are unlocked with request switch.
ANS BACK I-KEY LOCK
Horn Chirp
Horn chirp reminder when doors are locked with request switch.
Buzzer*
Buzzer reminder when doors are locked with request switch.
Off
No reminder when doors are locked with request switch.
HORN WITH KEYLESS LOCK
Off
Horn chirp reminder when doors are locked with Intelligent Key.
On*
No horn chirp reminder when doors are locked with Intelligent Key.
HAZARD ANSWER BACK
Lock/Unlock*
Hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
Unlock Only
Hazard warning lamp activation when doors are unlocked with Intel-
ligent Key or request switch.
Lock Only
Hazard warning lamp activation when doors are locked with Intelli-
gent Key or request switch.
Off
No hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
INSIDE ANT DIAGNOSIS
—
This function allows inside key antenna self-diagnosis.
CONFIRM KEY FOB ID
—
Intelligent Key ID code can be checked.
SHORT CRANKING OUTPUT
Start
70 msec
Starter motor operation duration time setting.
100 msec
200 msec
End
—
PANIC ALARM SET
MODE 3
1.5 sec
Intelligent Key panic alarm button setting.
MODE 2
OFF
MODE 1*
0.5 sec
LO- BATT OF KEY FOB WARN
On*
Intelligent Key low battery warning ON.
Off
Intelligent Key low battery warning OFF.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст