Nissan Versa Note. Manual — part 609
PCS-46
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
7
P
Cooling fan power supply
(LOW)
Output
ON
or
START
Cooling fan OFF
0V
Cooling fan LO
Battery voltage
Cooling fan MID
4 – 8 V
Cooling fan HI
Battery voltage
8
G
Battery power supply
Input
OFF
—
Battery voltage
9
BR
Fuel pump power supply
Output
ON
RUN
Approximately 1 second after
turning the ignition switch ON
6 – 16 V
ON
Approximately 1 second after
turning the ignition switch ON
0 - 1 V
10
L
Ignition switch power
supply (ON or START)
Input
OFF
0V
ON
or
START
Battery voltage
11
G
ECM relay power supply
Output
OFF
More than a few seconds after
turning ignition switch OFF
0 – 1 V
ON
OFF
For a few seconds after turning
ignition switch OFF
6 – 16 V
13
1
LG
Starter relay coil power
supply
Input
ON
Clutch released
0 – 1 V
Clutch depressed
Battery voltage
14
L
Headlamp LOW (LH)
power supply
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
Battery voltage
16
P
Headlamp LOW (RH)
power supply
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
Battery voltage
17
LG
Front wiper motor LOW
power supply
Output
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch LO
Battery voltage
18
GR
Front wiper motor HIGH
power supply
Output
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch HI
Battery voltage
19
B
Ground
—
—
—
—
20
BR
ABS actuator and electric
unit (control unit) power
supply
Output
OFF
—
0V
ON
or
START
—
Battery voltage
21
1
G
Clutch interlock switch
power supply
Output
OFF
or
ACC
0 – 1 V
ON
6 – 16 V
21
2
R
Transmission range
switch power supply
Output
OFF
or
ACC
0 – 1 V
ON
6 – 16 V
22
P
Illumination power supply Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
Battery voltage
23
R
Combination lamp power
supply
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
Battery voltage
24
W
Daytime light relay 1
power supply
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
Battery voltage
Terminal
Wire
color
Circuit
Input/
Output
Ignition
switch
Condition
Value
PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-47
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
25
G
Headlamp HIGH (LH)
power supply
Output
Lighting switch other than HI
and PASS
0 – 1 V
Lighting switch HI
Lighting switch PASS
Battery voltage
27
Y
Headlamp HIGH (RH)
power supply
Output
Lighting switch other than HI
and PASS
0 – 1 V
Lighting switch HI
Lighting switch PASS
Battery voltage
28
V
A/C compressor power
supply
Output
RUN
A/C switch OFF
0 – 1 V
A/C switch ON
(A/C compressor is operating)
Battery voltage
29
L/W
Throttle control motor re-
lay power supply
Output
OFF
More than a few seconds after
turning ignition switch OFF
0 – 1 V
ON
OFF
For a few seconds after turning
ignition switch OFF
6 – 16 V
32
G/W
Throttle control motor re-
lay control
Output
ON
→
OFF
0 – 1 V
↓
Battery voltage
↓
0 – 1 V
ON
0 – 1 V
34
Y
Ignition coil power supply
Output
OFF
or
ACC
0 – 1 V
ON
6 – 16 V
35
BR
NATS antenna amp pow-
er supply
Output
OFF
6 – 16 V
36
SB
Fuel injector power sup-
ply
Output
OFF
or
ACC
0 – 1 V
ON
6 – 16 V
39
L
Timing control solenoid
valve power
supply
Output
OFF
More than a few seconds after
turning ignition switch OFF
0 – 1 V
ON
OFF
For a few seconds after turning
ignition switch OFF
6 – 16 V
40
2
BR
Starter relay coil power
supply
Input
ON
Select lever in any position oth-
er than P or N
0 – 1 V
Select lever P or N
Battery voltage
43
GR
Fuel pump relay control
Output
ON
RUN
Approximately 1 second after
turning the ignition switch ON
0 – 1 V
ON
Approximately 1 second or
more after turning the ignition
switch
6 – 16 V
47
R/W
ECM power supply
Output
OFF
More than a few seconds after
turning ignition switch OFF
0 – 1 V
ON
OFF
For a few seconds after turning
ignition switch OFF
6 – 16 V
Terminal
Wire
color
Circuit
Input/
Output
Ignition
switch
Condition
Value
PCS-48
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
1
: With M/T
2
: With CVT
Fail-Safe
INFOID:0000000009578980
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM
48
O
Generator C
Output
OFF
or
ACC
0 – 1 V
ON
50
P
ECM relay control
Output
OFF
More than a few seconds after
turning ignition switch OFF
0 – 1 V
ON
OFF
For a few seconds after turning
ignition switch OFF
6 – 16 V
59
Y
Cooling fan relay control
Output
Cooling fan OFF or LO operated
Battery voltage
Cooling fan MID or HI operated
0 – 1 V
60
B
Ground
—
—
—
—
61
P
CAN-L
Input/
Output
—
—
—
62
L
CAN-H
Input/
Output
—
—
—
65
BR
Cooling fan relay power
supply
Output
OFF
or
ACC
0 – 1 V
ON
Battery voltage
69
GR
Daytime light relay 1 con-
trol
Output
Battery voltage
0 – 1 V
71
W
Front fog lamp relay con-
trol
Output
Front fog lamp switch OFF
Battery voltage
Front fog lamp switch ON
0 – 1 V
73
SB
Horn relay control
Output
Horn is not activated
Battery voltage
Horn is activated
0 – 1 V
74
V
Front wiper motor stop
position
Input
ON
Front wiper stop position
0 – 1 V
Any position other than front
wiper stop position
Battery voltage
Terminal
Wire
color
Circuit
Input/
Output
Ignition
switch
Condition
Value
JMMIA0842GB
Control part
Fail-safe operation
Cooling fan
• The cooling fan relay turn ON when the ignition switch is turned ON (Cooling fan HI oper-
ation)
• The cooling fan relay turn OFF when the ignition switch is turned OFF
A/C compressor
A/C relay OFF
Generator
Outputs the power generation command signal (PWM signal) 0%
PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-49
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
If No CAN Communication Is Available With BCM
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit of the ignition relay inside and ignition switch status
from BCM via CAN communication.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the ignition
switch status from BCM via CAN communication.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
DTC Index
INFOID:0000000009578981
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
Control part
Fail-safe operation
Headlamp
• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamp
• License plate lamp
• Illumination
• Tail lamp
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is
turned OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe
control is activated while the front wiper is set in the INT mode and the front wiper motor
is operating.
• Returns automatically wiper to stop position when ignition switch is turned ON if fail-safe
control is activated while front wiper motor is operated and wiper stop in the other position
than stop position.
Front fog lamp
Front fog lamp relay OFF
Horn
Horn OFF
Voltage judgment
IPDM E/R judgment
Operation
Ignition relay contact
side
Ignition switch status
from BCM
ON
ON
Ignition relay ON normal
—
OFF
OFF
Ignition relay OFF normal
—
ON
OFF
Ignition relay ON stuck
• Detects DTC “B2098: IGN RELAY ON”
• Turns ON the tail lamp relay for 10 minutes
OFF
ON
Ignition relay OFF stuck
Detects DTC “B2099: IGN RELAY OFF”
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст